Safety Information; Preparation - Homewerks SmartVent 7146-80-MS Manual Del Usuario

SAFETY INFORMATION

Please read and understand this entire manual before attem ting to assemble, operate or install the product.
•
Always disconnect the power supply prior to servicing
the fan, motor or junction box.
•
Follow all local building, safety and electrical codes
as well as NEC (National Electrical Code) and OSHA
(Occupational Safety and Health Act).
•
Electric Service supply must be 120 volts, 60 hertz.
•
This product must properly connect to the grounding
conductor of the supply circuit.
•
Do not bend or kink the power wires.
•
Do not use this fan with any solid state control device,
such as a remote control, dimmer switch, or certain
timers. Mechanical timers are not solid state devices.
•
Do not install in a ceiling with insulation greater than
R40.
•
Duct work should be installed in a straight line with
minimal bends.
•
Duct work size must be the same size as the discharge
and should not be reduced. Reducing the duct size
may increase fan noise.
CAUTION
•
For general ventilating use only. Do not
use to exhaust hazardous or explosive
materials and vapors.
•
Not for use in cooking areas.
•
To reduce the risk of injury to persons,
install the fan at least 7 feet (2.1m) above
the floor.
CAUTION: Installation of this unit requires the power to be OFF until installation is complete. If you encounter issues with the
unit not powering up, please review the troubleshooting section of the instruction manual.
If you require additional assistance, please call 1-877-319-3757, 7:30 a.m. - 4:30 p.m., CST, Monday - Friday.
DO NOT RETURN TO STORE.

PREPARATION

Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and
hardware contents. If any part is missing or damaged, do not attempt to assemble, install or operate the product. Contact
customer service for replacement parts at 1-877-319-3757, 7:30 a.m. - 4:30 p.m., CST, Monday - Friday.
Tools Required for Assembly (not included): Hammer, Flathead Screwdriver, Wire Connectors, Nails, Duct Tape, Phillips
Screwdriver, and Utility Knife or Drywall Saw.
Helpful Tools (not included): Electric Drill, Drill Bits.
All manuals and user guides at all-guides.com
1. Use this unit in the manner intended by the manufac-
2. Before servicing or cleaning unit, switch power off at
3. Installation work and electrical wiring must be done by
4. Sufficient air is needed for proper combustion and
5. When cutting or drilling into the wall or ceiling, do not
6. Ducted fans must always be vented to the outdoors.
7. If this unit is to be installed over a tub or shower, it must
8. This ventilation fan is intended to be installed at least
4
WARNING: To reduce the risk of fire, electric
shock, or injury to persons, observe the
following:
turer. If you have any questions, please call customer
service.
service panel and lock the service disconnecting means
to prevent power from being switched on accidentally.
When the service disconnecting means cannot be
locked, securely fasten a prominent warning device,
such as a tag, to the service panel.
a qualified person(s) in accordance with all applicable
codes and standards, including fire-rated construction.
exhausting of gases through the flue (chimney) of fuel
burning equipment to prevent backdrafting.Follow the
heating equipment manufacturer s guideline and safety
standards such as those published by the National Fire
Protection Association (NFPA), and the American Society
for Heating, Refrigeration and Air Conditioning Engineers
(ASHRAE) and local code authorities.
damage electrical wiring and other hidden utilities.
be marked as appropriate for the application and be
connected to a GFCI (Ground Fault Circuit Interrupter) -
protected branch circuit.
3 ft. 3-1/4 in. (1 m) from the showerhead when installing
over a bathtub or shower. Installation within a shower
stall is not recommended for this unit, unless the
3 ft. 3-1/4 in. (1 m) distance can be met.
HomewerksWW.com