Changing Tools; Setting The Routing Depth - Festool OF 1400 EQ Instrucciones De Uso Originales

English
Brake
The OF 1400 EBQ has an electronic brake which
brings the spindle with tool to a standstill within
approx. 2 seconds of the tool being switched off.
7.2

Changing tools

CAUTION
Risk of injury from hot and sharp insertion
tool
► Do not use any blunt or faulty insertion
tools.
► Wear protective gloves when handling an
insertion tool.
To change tools, turn the power tool upside
down.
Inserting the tool
► Insert the routing tool into the open collet
as far as possible or at least up to the
mark on the router shank.
If the collet [3A-2] cannot be seen due to
the union nut [3A-3], the routing
tool [3A-1] must be inserted into the collet
to the extent that the mark
projects beyond the union nut.
► Press the switch [1-14] for the spindle stop
on the right-hand side.
► Tighten the nut [1-15] using an open ended
spanner (WAF 24).
The spindle stop only jams the motor spin­
dle in one direction of rotation. Therefore,
there is no need to use a spanner for tight­
ening and loosening nuts. Instead, a ratch­
et can be moved backwards and forwards.
Removing the tool
► Press the switch [1-14] for the spindle stop
on the left-hand side.
► Undo the nut [1-15] using an open ended
spanner (WAF 24) until you can feel resist­
ance. Overcome the resistance by continu­
ing to turn the open ended spanner.
► Remove the router.
7.3 Changing the collets
Collets are available for the following shaft di­
ameters: 6.0 mm; 6.35 mm; 8.0 mm; 9.53 mm;
10.0 mm; 12.0 mm; 12.7 mm (See Festool cata­
logue or online at www.festool.com for the or­
der numbers)
► Completely unscrew the nut [1-15] and re­
move it together with the collet.
18
► Only insert a new collet into the spindle if a
nut is fitted and engaged.
► Gently screw in the nut. Do not tighten the
nut if no cutter is inserted.
7.4
The routing depth is set in three steps:
1. Set the zero point, see 7.5.
2. Specify the routing depth, see 7.6.
3. Clamp the routing depth, see 7.7.
7.5
► Release the clamp lever [1-6] so that the
depth stop [1-7] can move freely.
► Position the router with the router ta­
ble [1-9] on a level surface. Open the rotary
knob [1-5] and push the power tool down­
wards until the cutter sits on the surface.
► Clamp the power tool in this position by
closing the rotary knob [1-5].
► Press the depth stop [1-7] against one of
the three fixed stops of the rotatable step­
ped stop [1-8].
A screwdriver can be used to individually adjust
the height of each fixed stop.
► Push the indicator [1-3] downwards so that
no longer
it points to 0 mm on the scale.
If the zero position is incorrect, this can be
corrected using the screw [1-2] on the in­
dicator [1-3].
7.6
The required routing depth can be specified us­
ing either quick depth adjustment or fine depth
adjustment.
Quick depth adjustment
► Pull the depth stop [1-7] upwards until the
indicator [1-3] points to the required rout­
ing depth.
► Clamp the depth stop in this position using
the clamp lever [1-6].
Fine depth adjustment
► Clamp the depth stop using the clamp lev­
er [1-6].
► Set the required routing depth by turning
the adjusting wheel [1-4].
Turning the adjusting wheel by a mark
changes the routing depth by 0.1 mm. A
full rotation changes the routing depth by
1 mm. The maximum adjustment range for
the adjusting wheel is 8 mm.

Setting the routing depth

Setting the zero point
Specifying the routing depth