Mounting The Guard - Ego Power+ BCX3800 Manual Del Operador

Ocultar thumbs Ver también para BCX3800:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 29
EN
WARNING:
To prevent accidental starting that could
cause serious personal injury, always remove the battery
pack from the tool when assembling parts, making
adjustments, cleaning, or when not in use.
WARNING:
Never operate the tool without the guard
and bike handle firmly in place. Failure to comply could
result in possible serious personal injury.
MOUNTING AND ADJUSTING THE BIKE HANDLE
The brush cutter is stored as shown in Fig. B. Firstly,
loosen the wing bolt on the connecting joint and then lift
the bike handle 180° around the shaft (Fig. C), turn it 90°
anticlockwise to make it face the bump head (Fig. D).
Lastly, move it back and forth to achieve a comfortable
working position and tighten the bolt.
NOTICE:
Operating the machine with the bike handle
perpendicular to the shaft is only permitted.

MOUNTING THE GUARD

Loosen and remove the two screws from the guard (Fig. E),
align the guard mounting holes with the assembly holes and
then lock the guard onto the shaft base with the two screws,
together with two spring washers (Fig. F).
WARNING:
Make sure the guard is fixed according
to Fig. F, any reverse fixing will cause great danger!
WARNING:
When the brush cutter is equipped with
a trimmer head, the guard accessory must be mounted
onto the guard. Failure to comply could result in an
overly long cutting line and motor overload.
REPLACE THE TRIMMER HEAD WITH THE 3-TEETH
BLADE
1. Remove the power plug from the string trimmer.
2. Rotate the trimmer head to align the slot in the flange
with the shaft-locking hole in the gear case and insert a
stabilizer into the hole (Fig. G).
3. Rotate the trimmer head clockwise to remove it (Fig. G).
4. Remove the guard accessory by loosening the three
screws with washer (Fig. H)
5. The blade is shipped with a sheath. Before mounting
the blade onto the brush cutter, the sheath should be
removed by undoing the clamp wire from the hook on
the sheath (Fig. I1).
NOTICE:
To protect against injury, you have to wear
gloves prior to any operation with the 3-teeth blade.
8
56 VOLT LITHIUM-ION REAR MOTOR BIKE-HANDLE BRUSH CUTTER — BCX3800
6. Mount the inner flange and flange cover into its place
(Fig. I2).
7. Mount the blade onto the motor shaft, ensuring that the
surface of the blade is flush with the surface of the inner
flange bulge. Mount the outer flange and the nut (Fig. I3).
Pre-tighten the nut in a COUNTERCLOCKWISE direction
by hand.
8. Position the gear case against a solid surface for support.
With one hand hold the brush cutter shaft and the other
hand grasp the multi-function wrench to tighten the nut
following the directional arrow icon marked on the outer
flange (Fig. I4).
REPLACE THE 3-TEETH BLADE WITH THE TRIMMER
HEAD
Know the 3-teeth blade cutting unit as Fig. J1 shown. Then
disassemble 3-teeth blade and mount the trimmer head on
the brush cutter.
1. Rotate the blade to align the slot in the flange with
the shaft-locking hole in the gear case and insert a
stabilizer into the hole.
2. Position the gear case against a solid surface for
support. With one hand hold the brush cutter shaft
and the other hand grasp the multi-function wrench
to loosen the nut clockwise (Fig. I4).
3. Take out the nut, outer flange, blade from the brush
cutter (Fig. J2).
J-1 Shaft
J-3 Flange Cover
J-5 Outer Flange
J-7 Slot in the Flange
NOTICE:
When the 3-teeth blade is unused, to prevent
personal injury, mount the blade into its sheath.
4. Assemble the guard accessory to the brush cutter by
tighten three screws with washer (Fig.H).
Rotate the trimmer head anticlockwise to install it
(Fig. G). Follow the instructions in "LINE
REPLACEMENT" to load the cutting line.
NOTICE:
Failure to wind the line in the direction
indicated it will cause the trimmer head to operate
incorrectly.
J-2
Inner Flange
J-4
3-teeth Blade
J-6
Nut

Publicidad

Tabla de contenido
loading

Tabla de contenido