Warning Symbols - GBC SHREDMASTER PX08-04 Instrucciones

Please read and keep these
important safety instructions
For a full copy of the operating instructions, hints
& tips and troubleshooting guide, please visit
www.gbc.com/service-support-center
The following symbol which is
found on the product indicates
you could be seriously hurt or
killed if you open the machine.
DO NOT OPEN.
• Only use the unit for its intended purpose.
• The unit must only be connected to a supply voltage
corresponding to the electrical rating shown on the unit.
• Unit should be connected to a socket outlet near the equipment
that is easily accessible.
• Do not connect multiple adaptors or use with an extension cable.
• Failure to follow these instructions could result in damage/injury
and will invalidate your guarantee.
• Do not attempt to service or repair the unit yourself.
• Do not attempt to shred credit cards.
• Do not use this unit if the cable or plug have been damaged.
• When transporting the appliance, avoid uneven foors and
objects lying on the foor.
• Care should be taken when moving equipment to avoid any
unleveled surfaces.
• Please read all the safety information and the instructions.
The manufacturer is not liable for cases of material damage or
personal injury caused by incorrect handling or non compliance
with the safety instructions. In such cases, the warranty will be
voided.
• The device is intended for use indoors. Never use outdoors.
• Keep the device away from moisture.
• Be vigilant at all times, and always be careful what you are
doing. Do not use electrical equipment if you are lacking in
concentration or awareness, or are under the infuence of drugs,
alcohol or medication. Even a moment of inattentiveness can
lead to serious and injuries when using electrical equipment.
accidents
• Do not attempt to open, modify or repair the device. Do not drop,
puncture, break or expose to high pressure.
• Alterations to the device and technical modifcations are not
permitted.
• Check the device and cable (and if applicable, the adapter) for
any damage before use. If there is any visible damage, a strong
odour, or excessive overheating of components, unplug all the
components immediately and stop using the device.
• Do not shred continuously for more than 3 minutes at a time.
Running the unit for too long may cause the motor to overheat.
If the motor overheats, allow it to cool down for at least 60
minutes before resuming use.
• Do not use spray cleaners or spray lubricants as these may
present a risk of fash fre.
Indicators
Cooling down
4
4407 GBC Platform 1 - Shredmaster PX08-04 & PX06-04 Safety Booklet US_v3.indd 4
c
m
WARNING
Electrical shock hazard.
Do not open. No user
serviceable parts inside.
Refer servicing to qualifed
service personnel.
Controls
Shredder is operating
In reverse mode

Warning symbols

No CDs
Keep loose jewellery clear
No credit cards
Ties and loose clothing hazard
Keep long hair clear
No heavy duty paperclips
Do not reach into opening
This equipment is not intended for use by children
Do not use spray cleaners or spray lubricants as these
may present a risk of fash fre
Manual feed slot capacity
No heavy duty staples
Sharp edges, Do not touch
Moving parts
No aerosols
FCC Class B Notice
Note: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause
undesired operation
CANADA CLASS B NOTICE
This Class B digital apparatus complies with Canadian ICES-003
MODIFICATIONS
Any modifcations made to this device may void the authority
granted to the user by the FCC and/or by Industry Canada to
operate this equipment.
ACCO is a registered trademark of ACCO Brands.
Copyright © 2018 ACCO Brands. All rights reserved.
Issue August 2018
ShredMaster is a registered trademark of ACCO Brands
5/9/19 1:24 PM