Tabla de contenido
Publicidad
Apéndices
Aplicación MIDI
Modelo SP-808
1. RECOGNIZED RECEIVE DATA
Channel Voice Message
Note On/Off
Receive the note number which is designated with "RxNote", in the MIDI channel number
which is designated with "Pads Rx Ch." in the system parameter "2. Set MIDI Param?".
Receive only when the effect patch including VIRTUAL ANALOG SYNTH (algorithm 20) is
selected.
Status
Second
Third
9nH
mmH
llH
n = MIDI Channel No.:
00H–09H (ch.1–ch.10) (*1)
0AH (ch.11) (*2)
mm = Note No.:
00H–7FH (0–127)
ll = Velocity:
01H–7FH (1–127) / 00H = NOTE OFF
*1 Only receive pads.
*2 Only when the effect patch including VIRTUAL ANALOG SYNTH (algorithm 20) is
selected.
Control Change
Parameters on the Mixer section can be received and by the control change messages when
"Mixer,D-Beam" in the SYSTEM parameter ("2.Set MIDI Param?") is set to "SEND."
Status
Second
Third
BnH
mmH
llH
n = MIDI Channel No.:
mm = Mixer Parameter No.:
ll = Mixer Parameter Value:
Mixer Parameter and MIDI Channel/Control Change No.
<Mixer Channel Strip>
+—————————————————— Master
|
+——————————————— Track A
|
|
+———————————— Track B
|
|
|
|
|
|
|
|
|
|
|
|
MIDI ch.
11 12 13 14 15 16
Level
7 -> -> -> -> ->
Balance
10 -> -> -> -> ->
Effects Send Level
91 -> -> -> -> ->
AUX Send Level
92 -> -> -> -> ->
Bank select (MSB/LSB)
Switches the effect bank of Preset/User.
Status
Second
Third
BnH
00H
mmH
BnH
20H
llH
n = MIDI Channel No.:
mm = upper byte of bank number:
ll = lower byte of bank number:
Bank Select | Program Change
MSB | LSB |
——————+—————+————————————————————+————————————————————————
00H | 00H | 00H–62H (0–98)
00H | 40H | 00H–62H (0–98)
00H | 40H | 63H (99)
Program Change
Works as bank switch when MIDI channel number is set for playing the sample.
Works as Effects patches switch when channel number is set to 0AH.
Status
Second
CnH
ppH
n = MIDI Channel No.:
00H–09H (ch.1–ch.10)
0AH (ch.11)
pp = Program No.:
00H–63H (0–99)
170
Versión 1.00
Mar. 25 1998
0AH–0FH (ch.11–ch.16: see below)
(see below)
00H–7FH (0–127)
+————————— Track C
|
+—————— Track D
|
|
+——— MIC/LINE
|
|
|
0AH (ch.11)
00H
00H, 40H (0, 64)
| Patch Number
|
| Preset #01–#99
| Preset #01–#99
| master Isolator/Filter
System Common Messages
MIDI Time Code Quarter Frame Messages
The transmitted time counts are summed to "MTC Offset Time" as the song top is
"00:00:00:00". The SP-808 synchronizes with the time counts which are summed to "MTC
Offset Time" as the song top is "00:00:00:00" if the SONG parameter "Sync Source" is
"MTC".
Status
Second
F1H
mmH (= 0nnndddd)
nnn = Message type:
0 = Frame count LS nibble
1 = Frame count MS nibble
2 = Seconds count LS nibble
3 = Seconds count MS nibble
4 = Minutes count LS nibble
5 = Minutes count MS nibble
6 = Hours count LS nibble
7 = Hours count MS nibble
dddd = 4 bit nibble data:
0H–FH (0–15)
If the upper and lower 4 bits of the count are combined, these bit fields are assigned as
follows.
Frame Count
xxxyyyyy
xxx
Reserved (000)
yyyyy
Frame No. (0–29)
Seconds Count
xxyyyyyy
xx
Reserved (00)
yyyyyy
Seconds Count (0–59)
Minutes Count
xxyyyyyy
xx
Reserved (00)
yyyyyy
Minutes Count (0–59)
Hours Count
xyyzzzzz
x
Reserved (0)
yy
Time Code type
zzzzz
Hours
System Realtime Message
Start
Status
FAH
Continue
Status
FBH
Stop
Status
FCH
System Exclusive Message
Status
Data Bytes
F0H
iiH,ddH, ..., eeH
Byte
Description
F0H
Status of System Exclusive Message
iiH
Manufacturer ID
41H Roland's Manufacturer ID
7EH Universal Non Realtime Message
7FH Universal Realtime Message
ddH
Data: 00H–7FH (0–127)
|
|
eeH
Data
F7H
EOX (End of System Exclusive Message)
About Model ID
For Data Request (RQ1) and Data Set (DT1), SP-808 uses 00H 0FH as a Model ID.
0 = 24 Frames/Sec
1 = 25 Frames/Sec
2 = 30 Frames/Sec (Drop Frame)
3 = 30 Frames/Sec (Non Drop Frame)
Status
F7H
Publicidad
Tabla de contenido
