Fuel Safety; Safety Instructions For Maintenance - Husqvarna CT 36A/A-V Manual De Usuario

a) If the engine does not stop, push the handle
to the right with force again and again until the
engine stops. If the engine does not stop after
you try 5 times, it is necessary to repair the
gyroscopic safety switch.
b) Stop the engine and speak to an approved
Husqvarna service center. Refer to
product on page 37 .
WARNING:
product before the gyroscopic safety
switch is repaired.

Fuel safety

WARNING:
instructions that follow before you use the
product.
• Fuel is flammable and the fumes are explosive. Be
careful with fuel to prevent injury, fire and explosion.
• Do not breathe in the fuel fumes. The fuel fumes are
poisonous and can cause injury. Make sure that the
airflow is sufficient.
• Do not remove the fuel tank cap or fill the fuel tank
when the engine is on.
• Let the engine become cool before you refuel.
• Do not fill fuel in an indoor area. Not sufficient airflow
can cause injury or death because of asphyxiation or
carbon monoxide.
• Do not smoke near the fuel or the engine.
• Do not put hot objects near the fuel or the engine.
• Do not fill fuel near sparks or flames.
• Before you refuel, open the fuel tank cap slowly and
release the pressure carefully.
• Fuel on your skin can cause injury. If you get fuel on
your skin, use soap and water to remove the fuel.
• If you spill fuel on your clothing, change clothing
immediately.
• Do not fill the fuel tank fully. Heat causes the fuel to
expand. Keep a space at the top of the fuel tank.
• Tighten the fuel tank cap fully. If the fuel tank cap is
not tightened, there is a risk of fire.
• Before you start the product, move the product to a
minimum of 3 m/10 ft from where you refueled.
• Do not start the product if there is fuel or engine
oil on the product. Remove the unwanted fuel and
engine oil and let the product dry before you start the
engine.
• Examine the engine for leaks regularly. If there are
leaks in the fuel system, do not start the engine until
the leaks are repaired.
• Do not use your fingers to examine the engine for
leaks.
• Keep fuel in approved containers only.
• When the product and fuel is in storage, make sure
that fuel and fuel fumes cannot cause damage.
34
To stop the
Do not operate the
Read the warning
• Drain the fuel in an approved container outdoors and
away from sparks and flames.
Safety instructions for operation near edges
WARNING:
instructions that follow before you use the
product.
• There is a risk that the product falls when you
operate it near an edge. Always keep a minimum
of ⅔ of the product on a surface that is sufficiently
stable to hold the product weight.
• If the product falls, stop the engine before you lift the
product back to a surface that is sufficiently stable.
To lift the product with lifting equipment on
Refer to
page 42 .

Safety instructions for maintenance

WARNING:
instructions that follow before you use the
product.
• If the maintenance is not done correctly and
regularly, the risk of injury and damage to the
product increases.
• Use personal protective equipment. Refer to
Personal protective equipment on page 32 .
• Stop the engine and make sure that all parts of the
product are cool before you do the maintenance.
• Clean the product to remove dangerous material
before you do the maintenance.
• Disconnect the spark plug cap before you do the
maintenance.
• Worn blades can have sharp edges. Use protective
gloves and be careful around the blades.
• The exhaust fumes from the engine are hot and can
contain sparks. Do not operate the product in indoor
areas or near flammable material.
• Do not do modifications to the product. Modifications
that are not approved by the manufacturer, can
cause serious injury or death.
• Always use original accessories and spare parts.
Accessories and spare parts that are not approved
by the manufacturer, can cause serious injury or
death.
• Replace damaged, worn or broken parts.
• Only do the maintenance as given in this operator's
manual. Let an approved service center do all other
servicing.
• Remove all tools from the product before you start
the engine after maintenance. Loose tools or tools
attached to rotating parts can eject and cause injury.
• After maintenance, do a check of the vibration level
in the product. If it is not correct, speak to an
approved service center.
• Let an approved service center do servicing on the
product regularly.
Read the warning
Read the warning
1452 - 002 - 20.05.2022