Troubleshooting Guide - Good Earth Lighting GL1325-WHT-24LF1-G Manual De Instalación

Locate the keyhole slots on the top side of the endcaps.
1
1/8-in.
Dx2
1
The instructions provided do not cover growing methods; they only provide an overview of the role the grow light plays in plant development. Results from
indoor horticulture will vary based on soil nutrients, composition, moisture, air temperature, air flow, and the species of plant(s).
Locate the auto-timer on the endcap of the light near the "power-in" port. Light can be operated independently of the auto-timer feature.
This product features a continuous 24-hour auto-timer with three different timer-settings that control the light exposure given to the plants.
Timer is off.
16H: Light is
2
"ON" for 16
hours and
"OFF" for 8
hours.
TURN POWER OFF PRIOR TO LINKING!
To install additional units, follow installation steps 1 and
2. To link, plug the cord into the linking outlet of the
preceding fixture.
A maximum of (4) GL1326-WHT-24LFC-G fixtures can be linked together
in one run.
Care and Maintenance
Periodically clean the fixture and diffuser using a mild, nonabrasive cleaner and soft cloth. When cleaning the fixture, make sure the power is turned off. Do
not spray cleaner directly onto any part of the fixture or LEDs.
The information provided on the packaging should only be used as a suggestion. No guarantees of plant health or yield are guaranteed or inferred with the
use of these lights. Water, soil, fertilizers, temperature, environment, and other factors will impact plant health.
PROBLEM
Light does not come on.
Timer setting does not change.
Linking cord cannot be
inserted into either or both
units being linked.
2
Insert the connector end of the power cord into the "power-in" port located on the end of the fixture
with the slide dimmer. Make sure the plug is fully inserted into the port.
Plug fixture into an electrical outlet.
1
3

TROUBLESHOOTING GUIDE

POSSIBLE CAUSES
Power is shut off at light switch.
Power cord or linking cord is not properly connected.
Timer is currently running in "OFF" hour.
Auto-timer setting didn't change when changed.
Cord is being inserted in the wrong direction.
Fixtures need to be linked with the power connector
the same position/direction (power-in side first).
Slide timer switch to 'OFF' before pressing the rocker switch.
Press the "O" on the rocker switch to turn on.
Slide timer switch to 'OFF' before pressing the rocker switch on. When
12H: Light is
the timer is off, turn the light on and off manually by pressing the rocker
"ON" for 12 hours
switch.
and "OFF" for 12
Slide the timer switch to the suggested timer settings, 12H, 16H, or 20H.
hours.
The light will turn off automatically after 12 hours, 16 hours or 20 hours.
20H: Light is
"ON" for 20
NOTE: The timer is on a 24-hour cycle. The light will turn on
hours and "OFF"
automatically the same time everyday. Do not manually turn off the light
for 4 hours.
or cut the power supply. If that happens, reset the timer function by
sliding the timer switch to "OFF" and start the auto-timer steps, 1 to 2
again.
Verify light switch are on and a color button has been pressed.
Check cord connection.
Either reset timer, or wait for cycle to conclude.
Slide timer switch to the "OFF" position and make sure the
desired color button(s) is pressed and slide switch to timer setting.
Reverse cord and try inserting again. Plugs only fit one
specific way into the fixtures.
Rotate the last fixture so the power connector is first in-line.
Adjust the screws (D), leaving 1/8-in. clearance between
the mounting surface and the back of the screwhead.
Lift the fixture up to the mounting screws (D) and
simultaneously guide the screw heads through the large
round ends of the keyhole slots. Slide the fixture until the
screwheads are captured in the keyhole slots.
NOTE: If the fixture is loose, remove it and tighten each
screw 1/4 turn and reattach.
NOTE: The linking cord is designed to
attach one way and only one way into
the adjoining fixtures. If the plug cannot
be fully inserted into the fixture, reverse
the ends of the cord and try again.
CORRECTIVE ACTIONS
2