EINHELL TE-CL 18/2000 LiAC Manual De Instrucciones Original página 13

4. Operation
4.1 Installing the battery (Fig. 4)
Press the push/lock button of the battery pack
as shown in Fig. 4 and slide the battery pack into
the mount provided. Make sure that the push/lock
button engages properly. To remove the battery
pack, follow the steps in reverse order.
4.2 Charging the lithium battery pack
(Fig. 4/5)
1. Remove the battery pack (10) from the bat-
tery mount (8), pressing the push/lock button
(11) downward to do so.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
into the socket outlet. The green LED will then
begin to fl ash.
3. Push the battery pack onto the battery char-
ger.
In section 8 (Charger indicator) you will fi nd a
table with an explanation of the LED indicator on
the charger.
If the battery pack fails to charge, check for the
following:
•
whether there is a voltage at the mains power
socket;
•
whether there is good contact at the charging
contacts of the charging unit
If the battery pack still fails to charge, please send
•
the charging unit
•
and the battery pack
to our customer service center.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
Anl_TE_CL_18_2000_LiAC_SPK13.indb 13 Anl_TE_CL_18_2000_LiAC_SPK13.indb 13
GB
4.3 ON/OFF switch (Fig. 3 / item 3)
Warning:
Do not look into the light beam.
Switching on:
•
Press the ON/OFF switch (3).
•
For safety reasons, the lamp will always come
on in its lowest brightness setting.
Switching off :
•
Press the ON/OFF switch (3) again.
4.4 Adjusting the brightness (Fig. 3/ item 4)
Warning:
Do not look into the light beam.
•
Three different brightness settings are availa-
ble so that the lamp can be adjusted to the
particular lighting conditions.
•
For safety reasons, the lamp will always come
on in its lowest brightness setting.
•
To increase the brightness, press the bright-
ness control (4).
•
The brightness increases to the next level
every time you press the button.
•
The current brightness setting is displayed by
the brightness indicator (5).
4.5 Adjusting the lamp position
•
You can set the lamp to any position by rota-
ting the lamp head.
•
To do this, undo the fixing screw (6) on the
right-hand side of the lamp.
•
Then adjust the lamp to the required position
and retighten the fixing screw (6).
4.6 Operation with a power supply unit (9)
•
The lamp can also be used in conventional
fashion with the enclosed power supply unit
(9).
•
Check that your mains voltage is the same as
the one marked on the rating plate.
•
Plug the mains plug (9a) of the power supply
unit into the socket outlet.
•
Then connect the plug (9b) into the power
connection (7) of the lamp.
Note: You do not need to take out the battery
when you are operating the lamp with the po-
wer supply unit.
Note: The battery will not be charged when
you are operating the lamp with the power
supply unit.
- 13 -
06.07.2022 10:21:55 06.07.2022 10:21:55