Troubleshooting Guide; Warranty Information - Good Earth Lighting SE1296-BP2-02LF1-G Manual De Instrucciones

DANGER!
PROBLEM
Security light 1. Light switch is o .
does not come
2. Fuse is blown. Circuit breaker has tripped.
on.
3. Fixture not properly wired to J-box.
4. It is daylight.
5. Motion sensor is pointed in the wrong
6. Air temperature is about the same as a
Light continuously 1. Light sensor is triggered by reflected light
cycles ON and OFF
(strobe e ect).
2. Heat is being reflected from other sources
Light turns on 1. Light may be installed in shadows/dark
during daylight
hours.
Light comes on for
1. Sensor may be triggered by a small
no apparent reason.
2. Hot air (dryer vent, car exhaust, etc.) may
Light stays on
1. Motion sensor may be picking up a
continuously at
night.
2. Manual override may be activated.
Light flashes on 1. The TIMER control knob is set to TEST.
for 20 seconds at
a time, day or
night.
Good Earth Lighting - The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a period of
®
(6) years from the date of original purchase by the consumer. The fixture is not warrantied for use in a commercial or retail application. The
warranty is limited to use in a residential environment. We will repair or replace (at our option) the unit in the original color and style if
available, or in a similar color and style if the original item has been discontinued, without charge. Defective units must be properly packed
and returned to the manufacturer with a letter of explanation and your original purchase receipt showing date of purchase. Call
1-800-291-8838 to obtain a return authorization number and an address where to ship your defective product. Note: C.O.D. shipments will
NOT be accepted. The liability of the manufacturer is in any case limited to replacement of the defective light fixture product. The manufactur-
er will not be liable for any other loss, damage, labor costs, or injury which is caused by the product. This limitation upon the liability of the
manufacturer includes any loss, damage, labor costs, or injury which is (I) to person or property or otherwise; (II) incidental or consequential in
nature; (III) based upon theories of warranty, contract, negligence, strict liability, tort, or otherwise; or (IV) directly, or indirectly related to the
sale, use, or repair of the product. This warranty gives you specific rights, and you may also have other rights which vary from state to state.
REPLACEMENT PARTS LIST: Hardware Kit: ZH-SE1296F02
Need Help?
10
Good Earth Lighting
Good Earth Lighting

Troubleshooting Guide

Before doing any work on the fixture, shut o power supply
at the circuit breaker panel to avoid electrical shock.
POSSIBLE CAUSE
direction.
person's body temperature and the motion
sensor cannot "see" the person.
from the security light itself.
and may be triggering sensor on and o .
area.
animal or passing car.
be triggering the sensor.
continuous flow of warm air from an
air vent, dryer vent, or heat reflecting o a
surface.
6-Year Limited Warranty
Please visit our website at: https://goodearthlighting.com/contact-us or call the Customer Care Center
1-800-291-8838, 8:30 a.m.-5 p.m., CST, Monday-Friday.
1400 East Business Center Drive, Ste. 108 Mount Prospect, IL 60056
®
is a registered trademark of Good Earth Lighting, Inc. © 2022 Good Earth Lighting, Inc. REV08.22
®
CORRECTIVE ACTION
1. Turn light switch on.
2. Replace fuse. Turn the circuit breaker back on.
3. Reinstall light fixture.
4. Recheck at night.
5. Readjust motion sensor.
6. Decrease the RANGE control setting.
1. Change the position of the light head and aim light
away from the reflecting surfaces.
2. Decrease the RANGE control setting.
1. Light is operating as it was designed. Use manual
override if necessary.
1. Decrease the RANGE control setting as necessary.
2. Increase the RANGE control setting as necessary.
1. Reposition the motion sensor.
2. Wait until next day for internal dusk-to-dawn sensor
to detect next dusk-dawn cycle. Once light is
detected, this will allow motion sensor to return to
controlling the fixture.
1. Set the TIMER control knob somewhere between
1 and 10.
Printed in Vietnam