CAB CIDRA-RE C Manual De Instrucciones página 9

DIP 5 "Prelam."
DIP 6 BLC
DIP 7 SCA/LOCK
DIP 8 RADIO
The control unit has a series of self-diagnostics LED's which allow to check all functions:
LED PP It switches on when the Step-by-Step push button is pressed
LED STOP It switches off when the STOP push button is pressed
LED PHOT It switches off when the opening photocells are not aligned or if obstacles are present
LED I14 It switches off when the closing photocells are not aligned or if obstacles are present
LED I15 It switches on when the pedestrian button is activated
LED DL1 Green LED: It indicates the status of the gate:
Flashing LED : Unit powered by mains power supply and motors stopped
LED Off: Motors in opening phase
LED On : Motors in closing phase
LED DL2 Red LED: Used only for model CIDRA-RI (see radio configuration)
The CIDRA-RI C control unit is equipped with an incorporated radio module to receive signals from both fixed code and
variable code remote controls (see functions of Dip-switch 8), with frequency of 433.92MHz.
To use a remote control, its code should be copied first. The memorization procedure is shown hereunder. The device is
able to store up to 64 different codes in memory.
Normally the DL2 LED flashes with a 3-second pause in order to show that the unit is powered and the micro-processor
is working regularly.
To memorize a new transmitter with activation of the P.P. (step-by-step) function
- Press PGM button once for 1s, the DL2 LED starts flashing with 1s pause.
- Within 10s, press the transmitter push button which should be stored in memory with P.P. function.
To store a new transmitter code with pedestrian activation
- Press the PGM twice, each time for at least 1 second, the DL2 LED switches on with fixed light.
- Within 10s press the transmitter push button which should be memorized with pedestrian function.
To exit the programming mode, wait for 10s or press the PGM button for 1 second, the DL2 LED flashes again with a
3-second pause.
To delete all transmitter codes from memory
- Keep the PGM push button pressed for 15 seconds, the DL2 LED starts flashing rapidly and switches off at completion
of erasing.
- Release the PGM push button, the memory is now deleted and the DL2 led starts flashing regularly again with a
3-second pause.
NOTE:
The transmitters are stored in a EPROM (U5) memory which can be extracted from the control unit and inserted in a new
CIDRA-RI C control unit, should the control unit be replaced.
For safety reasons, the transmitter codes cannot be stored in memory during the motor opening/closing phases.
If, when entering the copying procedure of transmitters, the DL2 LED shows a long flash and switches off, this means
either the receiver memory is full and no further transmitter codes can be stored in memory, or the transmitter used is not
compatible.
Forewarning flashing light enabled or disabled
Off: disabled forewarning flashing light
On: enabled forewarning flashing light. The flashing light is activated 3 s before the starting of the
motor.
The lock function is enabled or disabled. This is recommended for oil-hydraulic motors in order to
keep the wing resting on the mechanical stop.
Off: disabled function of lock maintenance.
On: enabled function of lock maintenance. Every 60 min the control unit carries out a closing
operation of about 3s to keep the gate wing resting on the stop.
The operating mode of the terminals 18/19 output is selected.
Off: Output, open gate LED
On: Output, impulse for the control of the Lock card for electric lock.
The programmable code transmitters are enabled or disabled (Not used by CIDRA-RE C).
On: Radio receiver enabled only for variable code transmitters (rolling-code).
Off: Receiver enabled for variable code transmitters (rolling-code) and programmable code (self-
learning and Dip/switch) .
Built-in receiver configuration (ONLY CIDRA-RI C)
LED Diagnostics
9