Chicco ONE4EVER Manual De Instrucciones página 19

1. The stroller is delivered closed (Fig.1). Release the closing device,
push the front part of the stroller forward and, at the same time,
pull up on the handle until you hear a click informing you that the
stroller is completely open (Fig. 1A-1B).
2. Fit the front wheel into the appropriate hole until you hear a locking
click (Fig. 2). Repeat the same operation for the second front wheel.
3. Fit the rear wheel into the appropriate hole, aligning the flat part
of the pin with the matching shape on the hole in the frame (Fig.
3). Repeat the same operation for the other wheel.
To remove the front and rear wheels press the release mechanisms
in figures 3A-3B.
WARNING: Before using the stroller, make sure that the wheels are
firmly attached to the structure by pulling gently outwards.
SEAT UNIT 1 (0m+/48m)
ASSEMBLING SEAT UNIT 1
The seat can be assembled in the forward facing or rearward facing
configuration.
4. Use the button located on the backrest to open the seat until it is
fully open (Fig. 4-4A); raise the connectors for the bumper bar (Fig.
4B) and attach the bumper bar (Fig. 4C). To remove the bumper
bar press on the lateral buttons (Fig. 4D) and pull upwards.
WARNING: Always fasten your child with the safety harnesses. The
bumper bar IS NOT a device for containing your child.
WARNING: Never use the bumper bar to lift the product with your
child sitting in it.
Attach the seat unit to the lateral connectors on the stroller (Fig.
4E) until you hear a click, then pull forward on the hood to open
it (Fig. 4F).
5. SEAT UNIT 1 is a reversible seat. To change the position of the seat, re-
move it from the lateral connectors by pressing on the release buttons
and pulling the seat unit upwards (Fig. 5), then reconnect it to the stroll-
er in the opposite direction (Fig. 5A-5B), as described in point 4.
WARNING: Make sure the seat is installed properly by pulling
it upwards.
WARNING: Do not remove the seat from the stroller when the child
is inside it.
ADJUSTING THE BACKREST ON SEAT UNIT 1
6. The height of the backrest can be adjusted to 3 positions: pull up on
the strap located on the rear to increase the height of the backrest
(Fig. 6). To reduce the height press down on the backrest (Fig. 6A).
Each position will be signaled by a click when it locks into place.
7. The backrest can be reclined in 4 positions. To recline, use the lever
located on the rear (Fig.7). To raise the backrest push upwards until
the desired position is reached (Fig. 7A).
SEAT UNIT 1 HOOD
The included hood is attached to the seat unit and is detachable.
8. The hood can be extended by opening the zip fastener (Fig. 8). An
expandable visor is present for added protection (Fig.8A).
9. To remove the hood unfasten the zip that connects the hood to the
backrest (Fig.9) and remove the two lateral plastic connectors from
the backrest (Fig. 9A). Next, free the fabric from the plastic pins on
either side (Fig.9B) and pull up on the hood, releasing the metal rod
from its housing (Fig.9C).
To reassemble follow the steps described above in reverse order.
WARNING: The hood must be fixed on both sides of the stroller.
Ensure that the canopy is correctly fastened.
FOLDING AND UNFOLDING THE STROLLER WITH SEAT UNIT 1
The stroller can be folded either without the seat or with the seat (in
either configuration: forward facing or rearward facing).
To ensure that the stroller folds properly, keep the bumper bar at-
tached to the seat.
10. Folding the stroller with seat forward facing. Position the back-
rest in the lowest configuration; rotate the backrest forward act-
ing on the lever located on the rear of the backrest (Fig. 10); once
the backrest has been folded onto the seat (Fig. 10A), rotate the
seat back towards the handle (Fig.10B-10C). Move switch "A" on
the handle either to the left or to the right while also pressing on
button "B" (Fig. 10D); push the handle forward (Fig. 10E) and the
stroller will fold by itself. The stroller will automatically lock in the
folded position (Fig. 10F).
11. Folding the stroller with seat rearward facing. Position the back-
rest in the lowest configuration; using the lever located on the
rear, rotate the backrest toward the seat until it folds completely
(Fig.11). Move switch "A" on the handle either to the left or to the
right while also pressing on button "B" (Fig. 11A); push the han-
dle forward (Fig. 11B) and the stroller will fold by itself (Fig. 11C).
12. To unfold the stroller, in whatever configuration (forward facing
or rearward facing) the steps are the same. Release the lever lock
found on the side of the stroller (Fig.12) and have the front legs
slide into place while pulling the handle upwards at the same
time until the stroller is completely open.
Use the lever located behind the backrest to open the seat (Fig.
12A), and raise the bumper bar (Fig.12B).
STROLLER SAFETY HARNESS
13. The stroller comes with a five-point safety harness which con-
sists of two shoulder straps, two waist straps and a crotch strap
with a buckle.
WARNING: When using with children aged 0 to 6 months, you may
have to shorten the length of the straps to adjust them to your baby.
WARNING: FOR USE WITH CHILDREN AGED 0 TO 6 MONTHS THE
BACKREST MUST BE ADJUSTED TO THE LOWEST POSSIBLE POSITION
(Fig. 13).
Make sure the shoulder straps are at a suitable height for your child.
If they are not, adjust their height (Fig. 13A) and repeat the same
operation for the waist strap as well. After putting the child in the
stroller, fasten the straps by passing the two waist clips (A) through
the buckles on the shoulder straps (B), and secure in the crotch strap
buckle (C) (Fig. 13B). To unfasten the waist straps press the button
in the middle of the buckle and pull the two extremities away from
the buckle (Fig.13C).
WARNING: To ensure the safety of your child, you must use the
crotch strap, waist belt and safety harness at the same time.
FITTING/REMOVING THE LINING ON SEAT UNIT 1
For greater comfort during the operation, position the backrest in
the highest possible configuration.
14. Remove the Comfort Kit, which consists of padded shoulder
straps and crotch strap (Fig.14). Unfasten the buttons on either
side of the backrest's fabric lining (Fig. 14A). Pass the shoulder
straps through the slots on the backrest fabric (Fig. 14B), detach
from the velcro on the rear (Fig. 14C) and remove the fabric flap
on the back (Fig.14D) being sure to properly remove the back-
rest height adjustment strap from the fabric.
15. After having removed the fabric cushion (Fig. 15), detach the flap on
the rear of the backrest using the two buttons (Fig. 15A) and proper-
ly free the backrest height adjustment control (Fig. 15B). Detach the
central padding from the support by means of the velcro segments
on either side (Fig. 15C) and pull the fabric downwards so that it
passes under the frame of the adjustable backrest (Fig. 15D).
16. Unfasten the two buttons on the seat from the lateral connectors
(Fig. 16); remove the waist straps from the slots (Fig. 16A) and un-
fasten the two buttons from the plastic support on the rear (Fig.
16B). Detach the fabric flap located under the seat from the velcro
that wraps around the tube (Fig. 16C) and open the strap indicat-
ed in the figure (Fig. 16D). Complete the operation by removing
the fabric from the bumper bar supports on either side (Fig. 16E).
To fit the lining on the seat, follow these same steps in the reverse order.
KIT COMFORT
The Comfort Kit comprises 2 shoulder pads and a padded crotch
strap and is shared by the two seat units.
17. Insert the shoulder pads on the straps and insert the buckle in
the padded crotch strap (Fig. 17-17A).
SEAT UNIT 2 (6m+/48m)
ASSEMBLING SEAT UNIT 2
Seat unit 2 can only be assembled in the forward facing configuration.
19