Introduction; Device Description (Fig. 1-26) - Parkside PMTS 210 A1 Instrucciones De Utilización Y De Seguridad

2. Introduction

Manufacturer:
scheppach
Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
Dear Customer,
We hope your new tool brings you much enjoyment and suc-
cess.
Note:
In accordance with the applicable product liability laws, the
manufacturer of this device assumes no liability for damage to
the device or caused by the device arising from:
• Improper handling
• Failure to comply with the operating manual,
• Repairs carried out by third parties, unauthorised specialists.
• Installing and replacing non-original spare parts,
• Improper use
• Failures of the electrical system in the event of the electri-
cal regulations and VDE provisions 0100, DIN 57113 /
VDE0113 not being observed.
Note:
Read the whole text of the operating manual before assembly
and commissioning.
This operating manual should help you to familiarise yourself
with your device and to use it for its intended purpose.
The operating manual includes important instructions for safe,
proper and economic operation of the device, for avoiding
danger, for minimising repair costs and downtimes, and for
increasing the reliability and extending the service life of the
device.
In addition to the safety instructions in this operating manual,
you must also observe the regulations applicable to the opera-
tion of the device in your country.
Keep the operating manual at the device, in a plastic sleeve,
protected from dirt and moisture. They must be read and care-
fully observed by all operating personnel before starting the
work.
The device may only be used by personnel who have been
trained to use it and who have been instructed with respect to
the associated hazards. The required minimum age must be
observed.
In addition to the safety instructions in this operating manual
and the separate regulations of your country, the generally
recognised technical rules relating to the operation of such ma-
chines must also be observed.
We accept no liability for accidents or damage that occur due
to a failure to observe this manual and the safety instructions.

3. Device description (fig. 1-26)

1. Saw table
2. Transverse stop
3. Riving knife
4. Saw blade guard
4a. Wing nut with washer (saw blade guard)
4b. Carriage bolt (saw blade guard)
4c. Extraction port (saw blade guard)
5. Saw blade
6. Table inlay
7. Parallel stop, complete
8. Handwheel (cutting depth adjustment)
8a. Handwheel (cutting angle adjustment)
9. Locking screw (cutting angle adjustment)
10. Overload switch
11. On/off switch
12. Rubber foot (4x)
13. Tool hook
14. Push stick
15. Locking screw (parallel stop) (2x)
15a. Clamping plate (parallel stop) (2x)
16. Holder (parallel stop)
16a. Screw (parallel stop)
17. Stop rail (for parallel stop or transverse stop)
18. Knurled screw (transverse stop)
19. Turning handle (parallel stop)
20. Ring spanner 7/8 mm
21. Ring spanner, 19/10 mm
22. Table width extension
23. Guide tube (table width extension)
24. End piece (table width extension) (2x)
25. Screw (for end piece of table width extension;
2x M3x8 self-tapping)
26. Knurled screw (table width extension)
27. Guide bushing (table width extension)
28. Height adjustment screw (table width extension)
29. Counternut (height adjustment screw)
30. Support foot (table width extension)
31. Hole (riving knife)
32. Screw (table inlay)
33. Fixing screw (riving knife)
34. Screw (saw blade cover)
35. Saw blade cover
36. Extraction port
37. Groove (stop rail for thick material)
38. Scale
39. Groove (stop rail for thin material)
40. Groove (saw table)
41. Mains cable
42. Bracket for workbench mounting (2x)
43. Screw (2x; M3x8 self-tapping)
44. Washers (2x; d 4mm)
45. Wood screw (for workbench mounting)
46. Holder (parallel stop)
GB/IE 3