Stop The Machine; Empty The Collection Bin; Assemble The Charging Station; Remove The Charger - GreenWorks VUG403 Manual Del Operario

The LED lights on the screen appear blue under normal
circumstances. If the LED lights turn to red and the machine
shut down automatically, please refer to chapter
'troubleshooting' to solve the problem.
8.2

STOP THE MACHINE

1. Press trigger (15) again to stop the machine.
8.3

EMPTY THE COLLECTION BIN

Figure 6
NOTE
Empty the collection bin after each use.
1. Press the button on the extension pole or accessories to
remove it from the vacuum head.
2. Push the bin release button (7).
3. Press the latch (2) to open the collection bin.
4. Dump debris from the bin into the waste basket.
8.4 ASSEMBLE THE CHARGING
STATION
Figure 7
You can mount the charger on the wall or the stand charger
base. The way you mount your charger will depend on the
model number and/or parts purchased.
Install the stand charger
1. Align the hole on the two-section rods (30) with the
release buttons on the connecting rod, and insert the two-
section rods to the connecting rod (14).
2. Align the hole on the rod (30) with the release button on
the bottom base, and insert the rod (30) to the bottom
base (31). Align the release button on the charger base
with the hole on the rod, and insert the charger base (32)
into the rod (30).
3. Align the ribs of the charger base (32) to the ribs of the
charger (21), then push the charger (21) into place. When
you hear a click, the charger is installed.
4. Align the power cord into the groove in the rod then
connect the charger and power source.
5. Lift and hang your machine onto the port. Clip the
accessory clip (24) to the extension pole or stand charger
to store the rest nozzles.
Wall-mounted charger
1. Drill two aligned holes on the wall, and knock the two
shrink tubes (33) into the holes. Put 2 screws (34) into the
shrink tubes to attach the charger base (35) on the wall.
NOTE
NOTE
English
2. Align the ribs of the charger accessory rack (23) to the
ribs of the charger (21) then push the rack lock into place.
When you hear a click, the rack is installed.
3. Align the ribs of the charger base (35) to the ribs of the
charger (21) then push the charger lock into place.
4. Lift and hang your machine onto the port. Clip the
accessory clip (24) to the extension pole to store the rest
nozzles or use the rack (23).
To remove the accessory rack (23), press the release button
(22) and pull the rack out.
8.5

REMOVE THE CHARGER

Figure 7-1 ~ 7-1.
1. Press the charger release button to remove the charger.
2. Press inward the rod release buttons to remove the rod.
9

MAINTENANCE

Do not let brake fluids, gasoline, petroleum-based materials
touch the plastic parts. Chemicals can cause damage to the
plastic, and make the plastic unserviceable.
Do not use strong solvents or detergents on the plastic
housing or components.
Remove the battery pack from the machine before
maintenance.
9.1

CLEAN THE FILTER

Figure 8-11
• Clean the vac filter on a regular basis to maintain
optimal performance.
• Cleaning should be done outdoors and not in the living
quarters.
• You can use a small brush to clean the dust and debris.
1. Press the button on the extension pole or accessories to
remove them from the vacuum head.
2. Push the bin release button then press the latch to open
the collection bin.
3. Dump debris from the bin into the waste basket.
4. Turn the filter assembly (6) counter-clockwise and take it
off the vacuum.
5. Keep the collection bin door open, carefully pull the filter
(25) out of the collection bin.
7
NOTE
CAUTION
CAUTION
WARNING
TIP
EN