Cebora CP-162C Manual Del Usuario página 10

V
V
V
B
T
• Connect connector B, introduce the
body into the grip seat and then connect connector A by
introducing it inside the grip as shown in igure 4.
• Reposition LH grip making sure not to latten any wire
between the grip rims.
• Screw in the 6 screws V again.
5.3.2 Replacing the welding torch body CP162C MAR
• Unscrew the cable gland F Fig.7;
• Unscrew the retention dowels G1 and G2, then handle
M, pull it back until all cables are shown (see Fig. 8).
• Disconnect connector A and connector B (pilot arc).
• Remove heat shrinking hose C and unscrew nut D
(wrench #13) by keeping itting E (wrench #11) fastened.
• Replacing the welding torch body.
• Screw in ittings D and E according to the arrow
direction - Fig .8
• Tighten ittings, introduce the heat-shrinking hose C
and use a small heat source to warm it up. Make sure
that ittings are completely covered.
• Reconnect connectors A and B, screw in the handle M
and then, the retention dowels G1 and G2.
• Screw again cable gland F.
10
All manuals and user guides at all-guides.com
V
V
V
Fig. 3
B
C
E D
A
Fig. 4
Fig. 5
welding torch
5.4 REPLACING THE GRIP WITH PUSH-BUTTON CP-
162C MAR
• Unscrew the 6 screws V Fig.3 and remove the LH grip.
• With reference to Fig.4, lift the welding torch body with
cable and disconnect connector A (push-button) .
• Replace the grip with push-button, connect connector
A and introduce it inside the grip, as shown in igure 4,
and then position the welding torch body with cable
inside the RH grip seat.
• Fasten the LH side of the grip making sure not to latten
any wire between the grip rims and then screw the 6
screws V again.
5.5 REPLACING THE
ADAPTER.
5.5.1 CP162C MAR
B
A
T
Fig. 6
• Tighten ittings, introduce the heat-shrinking hose C
and use a small heat source to warm it up.
• Connect connector B, introduce the welding torch
body into the grip seat and then connect connector A
by introducing it inside the grip as shown in igure 4.
• Reposition LH grip making sure not to latten any wire
between the grip rims.
• Screw in the 6 screws V again.
5.5.2 CP162C DAR
• Remove cable gland F Fig.7.
• Unscrew the retention dowels G1 and G2, then handle
M and pull it back until all cables are shown (see Fig. 8);
• Disconnect connector A and connector B (pilot arc).
• Remove heat shrinking hose C and unscrew nut D
(wrench #13) by keeping itting E (wrench #11) fastened.
• Replacing the welding torch cable.
• Screw in fittings D and E according to the arrow direction - Fig.8.
• Tighten ittings, introduce the heat-shrinking hose C
and use a small heat source to warm it up. Make sure
that ittings are completely covered.
CABLE WITH CENTRAL
• Unscrew the 6 screws V
Fig.3 and remove the LH
grip. With reference to
Fig.4, lift the welding
torch body with cable
and disconnect
connector A (push-
button) and connector B
(pilot arc).
• Remove
shrinking hose C and
unscrew nut D (wrench
#13) by keeping itting E
(wrench #11) fastened.
• Replace
welding torch cable,
manually screw ittings
D and E according to the
arrow direction - Fig.6.
heat
the