Device Configuration; Technical Parameters; Maintenance / Cleaning - 2N IP Style Manual Del Usuario

• Press and hold the CONTROL button.
• Connect the device to the power supply.
• Keep holding the button for a few seconds and then release it.
• Do not touch the display during restart, it is being calibrated.

Device Configuration

Configuration takes
interface. Alternatively, configuration is possible using
2N® Access Commander software or the My2N service.
The device is factory-set to DHCP ON. DHCP settings can be
switched directly on the display of the unit after switching to
the hidden menu in the following manner: Wait until the end
of the introductory animation on the display after starting/
restarting the device. The moment the home screen appears
(after approx. 20 s), place your finger in the top left corner of
the display for approx. 5 s.
The IP address of the device will also be shown in the hidden
menu. This can also be ascertained using the 2N® Network
Scanner tool which can be freely downloaded from www.2n.com

Technical Parameters

Basic properties:
• made of tempered glass and aluminium
• 10" capacitive touchscreen display with TFT LCD
technology with resolution of 2560 x 1920
• camera with infrared illumination and support for
streaming of up to 5 Mpix
• integrated combined reader
• tamper switch to detect unauthorized opening of the
device
• IP65 protection
• IK 08
• dimensions: 170 (w) x 355 (h) mm
o x 40 mm (d) for surface mounting
o x 22 mm (d) for flush mounting
Access control options:
• combined RFID card reader: 125 kHz and 13.56 MHz
(optionally secure version)
• numeric touchpad: numeric PIN code
• 2N® Mobile Key application: access using a smartphone
which supports NFC and Bluetooth technology
Interface:
Power Supply: 12 V ±15 % / 4 A DC or PoE+ (802.3at)
•
Maintenance – Cleaning
The surface will become dirty during use of the device. Use
a piece of soft cloth moistened with clean water to clean the
device.
You are recommended to follow the principles below while
cleaning:
Use suitable products designed for cleaning glasses, optical
devices or screens, etc. to clean the display. Clean the device in
dry weather in order to make waste water evaporate quickly. We
Caution
Always use the product for the purpose it was designed and
•
manufactured for, in compliance herewith.
• Any use of the product that is in contradiction with the
instructions provided herein may result in malfunction,
damage or destruction of the product.
• Any use or connection of the product other than those included
herein shall be considered undue and the manufacturer shall
not be liable for any consequences arisen as a result of such
misconduct.
• Be careful while handling the product; the manufacturer
shall not be liable for any personal injury or property damage
associated with the device.
2N TELEKOMUNIKACE a.s. hereby declares that the 2N® IP Style device type complies with the requirements of Directive 2014/53/EU and Directive
2011/65/EU. Refer to www.2n.com/declaration for the full wording of the EU Declaration of Conformity.
place typically via a Web If the address is 0.0.0.0, then the device did not get the IP
address from the DHCP server and static IP address (DHCP
OFF) has to be used. If DHCP OFF is set, the device static
address is 192.168.1.100.
Enter the IP address of the device shown into any web
browser. Accept the safety warnings of some browsers as your
acceptance is not in contradiction to a safe use of your device.
The factory login data are: username: admin and password: 2n.
Once logged in, you can start configuring your device via the
web interface. Detailed information about configuration is
provided by the Configuration manual for 2N IP intercoms which
is available at wiki.2n.com, a direct link is available on the start
screen of the configuration interface.
• LAN: 10/100BASE-TX s Auto-MDIX, RJ-45
• Recommended cabling: Cat-5e or higher
• Passive switch: make and break contact,
max. 30 V / 1 A AC/DC
• Active switch output: 12 V / 0.6 A DC
• Supported protocols: SIP2.0, SIPS, DHCP opt. 66,
SMTP, SNMP, TR069, 802.1x, RTSP, RTP, SRTP, TFTP,
HTTP, HTTPS, Syslog, ONVIF
Audio properties
• 2 built-in microphones
• Amplifier: 2 x 4 W
• Speaker: 2 x 4 W / 4 Ω
• LINE OUT: 1 VRMS / 600 Ω
• Full duplex audio
• Codecs: L16 / 16kHz, G.711, G.729, G.722
• Protocols: RTP/RTSP/SRTP
Video properties
• Frame rate: up to 60 frames/s
• Focal length: 1.7 mm
• Codecs: H.264, MJPEG
• Protocols: RTP/RTSP/SRTP/HTTP
• Camera functions: yes, ONVIF profile T compatible
recommend you to use IT cleaning wipes.
To disinfect the surface of the device against bacteria and
viruses (anti-covid) to maintain the hygiene conditions of
critical surfaces and touch points, we recommend that you use
Zoono – Microbe Shield Surface Sanitiser Spray.
Do not use aggressive detergents (such as abrasives or strong
disinfectants). Alcohol, peroxide and lye (caustic soda) based
cleaners must not be used.
The warranty does not apply to the product defects
•
and failures arisen as a result of improper mounting (in
contradiction herewith). The manufacturer is neither liable
for damage caused by theft within an area that is accessible
after the attached electric lock is switched on. The product is
not designed as a burglar protection device except when used
in combination with a standard lock, which has the security
function.
This manual is a brief version of the online User Manual
•
available at wiki.2n.com. In the event of any discrepancy
between the two aforementioned versions, the online version
shall prevail.
3