Klein Tools NCVT-1XTKIT Manual De Instrucciones página 2

Ocultar thumbs

página de 4

/ 4
Marcadores

Idiomas disponibles

ENGLISH

GENERAL SPECIFICATIONS

The Klein Tools NCVT-1XT is a durable 70 to 1000V AC non-contact voltage tester

with IP67 rating and a 3m (9.8') drop protection.

• Environment: Indoor

• Measurement Range: 70 to 1000V AC

• Frequency Range: 50 to 500 Hz

• Batteries: 2x AAA 1.5V Alkaline

• Operating and Storage Altitude: Up to 6562 ft. (2000 m)

• Operating and Storage Temp: 14° to 122°F (-10° to 50°C)

• Relative Humidity: <95% non-condensing

• Dimensions: 5.34" x 1.08" x 0.97" (135.6 x 27.4 x 22.1 mm)

• Weight: 1.65 oz (46.7 g) with batteries

• Pollution degree: 2

• Safety Rating: CAT IV 1000V AC

• Drop Protection: 9.8 ft. (3 m)

• Ingress Protection: IP67

• Standards: EN 61010-1:2010+A1: 2019,

EN IEC 61010-2-030:2021+A11:2021.

Conforms to UL STD. 61010-1, 61010-2-030

Certi ed to CSA STD. C22.2 No. 61010-1, 61010-2-030.

5001748

Specifications subject to change.

WARNINGS

To ensure safe operation and service of the tester, follow these instructions.

Failure to observe these warnings can result in severe injury or death.

• Risk of electric shock and burn. Contact with live circuits could result in death or serious

injury.

• Use caution with voltages above 25V AC as a shock hazard may exist.

Use caution with voltages above 25V AC as a shock hazard may exist.

• A blinking LED or a steadily illuminated LED in the tip and audible beeps indicate presence

A blinking LED or a steadily illuminated LED in the tip and audible beeps indicate presence

of voltage. If no indication, voltage could still be present.

• Before and after each use, verify operation by testing a known working circuit that is within

Before and after each use, verify operation by testing a known working circuit that is within

the rating of this unit.

• Never assume neutral or ground wires are de-energized. Neutrals in multi-wire branch

Never assume neutral or ground wires are de-energized. Neutrals in multi-wire branch

circuits may be energized when disconnected and must be retested before handling.

• The tester

The tester

WILL NOT

WILL NOT detect voltage if:

detect voltage if:

• The wire is shielded.

The wire is shielded.

• The operator is not grounded or is otherwise isolated from an effective earth ground.

The operator is not grounded or is otherwise isolated from an effective earth ground.

• The voltage is DC.

The voltage is DC.

• The tester

The tester

MAY NOT

detect voltage if:

• The user is not holding the tester.

The user is not holding the tester.

• The user is insulated from the tester with a glove or other materials.

The user is insulated from the tester with a glove or other materials.

• The wire is partially buried or in a grounded metal conduit.

The wire is partially buried or in a grounded metal conduit.

• The tester is at a distance from the voltage source.

The tester is at a distance from the voltage source.

• The field created by the voltage source is being blocked, dampened, or otherwise

The field created by the voltage source is being blocked, dampened, or otherwise

interfered with.

• The frequency of the voltage is not a perfect sine wave between 50 and 500Hz.

The frequency of the voltage is not a perfect sine wave between 50 and 500Hz.

• The tester is outside of operating conditions (listed in Specifications section).

The tester is outside of operating conditions (listed in Specifications section).

• Operation may be affected by differences in socket design and insulation thickness and

Operation may be affected by differences in socket design and insulation thickness and

type; tester may not be compatible with some types of standard or tamper resistant (TR)

electrical outlets.

• In bright light conditions, the LED visual indicators will be less visible.

In bright light conditions, the LED visual indicators will be less visible.

• When powered-ON, one of the "power-ON" LED's will be illuminated, and a green light

When powered-ON, one of the "power-ON" LED's will be illuminated, and a green light

will illuminate the tip.

DO NOT USE TESTER UNLESS ONE OF THE "POWER-ON" LED

ILLUMINATED.

• Do not use if tester appears damaged or is not operating properly. If in doubt, replace the

Do not use if tester appears damaged or is not operating properly. If in doubt, replace the

tester.

• Do not apply more than the rated voltage as marked on the tester (1000V).

Do not apply more than the rated voltage as marked on the tester (1000V).

• Do not apply to uninsulated hazardous live conductors.

Do not apply to uninsulated hazardous live conductors.

• Detection above 70V AC is specified under "normal" conditions as detailed below. The tester

Detection above 70V AC is specified under "normal" conditions as detailed below. The tester

may detect at a different threshold at different conditions, or may not detect at all unless:

• The tip of the tester is within 0.25" (6 mm) of an AC voltage source radiating unimpeded.

The tip of the tester is within 0.25" (6 mm) of an AC voltage source radiating unimpeded.

• The user is holding the body of the tester with his or her bare hand.

The user is holding the body of the tester with his or her bare hand.

• The user is standing on or connected to earth ground.

The user is standing on or connected to earth ground.

• The air humidity is nominal (50% relative humidity – non-condensing).

The air humidity is nominal (50% relative humidity – non-condensing).

• The tester is held still.

The tester is held still.

• Always wear approved eye protection.

Always wear approved eye protection.

• Comply with local and national safety requirements.

Comply with local and national safety requirements.

• If this product is used in a manner not specified by the manufacturer, protection provided

If this product is used in a manner not specified by the manufacturer, protection provided

by the product may be affected.

CAUTION

• DO NOT attempt to repair this tester. It contains no serviceable parts.

DO NOT attempt to repair this tester. It contains no serviceable parts.

DO NOT

attempt to repair this tester. It contains no serviceable parts.

• DO NOT

DO NOT

DO NOT expose tester to extremes in temperature or high humidity.

expose tester to extremes in temperature or high humidity.

NCVT-1XT

FUNCTION BUTTONS

NCV POWER ON/OFF BUTTON

Press and release the NCV Power button

single beep, the Power On Indicator

will illuminate. To power-OFF the tester, press and release the Power

On / Off button

. The tester will emit a double beep.

NOTE: The tester will automatically power-OFF following 4

minutes of inactivity to conserve battery life.

OPERATING INSTRUCTIONS

CHECKING FOR THE PRESENCE OF AC VOLTAGE

1. Press the Power On / Off button. After performing a self-test,

a green LED

will illuminate the tip when no voltage is

detected.

2. Prior to use, test on a known live circuit to verify tester

functionality.

3. Place tip of the tester

near AC voltage. If voltage is present,

the unit will emit audible beeps and the red LED

will illuminate.

SILENT OPERATION

To activate silent operation, power-ON by pressing and holding

the NCV Power-ON button

for more than 2 seconds. Power-

ON in this manner each time silent operation is desired.

MAINTENANCE

BATTERY REPLACEMENT

When the battery is low, the unit will power-on with a blinking red

LED

. When this happens, the batteries must be replaced:

1. Unscrew the battery cap

and remove/recycle spent

batteries.

2. Install two new AAA batteries. Note proper polarity.

3. Screw battery cap tightly to ensure a tight seal with the O-Ring

CLEANING

Be sure tester is turned off and wipe with a clean, dry lint-

free cloth. Do not use abrasive cleaners or solvents.

STORAGE

Remove the batteries when not in use for a prolonged period

of time. Do not expose to high temperatures or humidity. After

s IS

a period of storage in extreme conditions exceeding the limits

mentioned in the General Specifications section, allow the tester

to return to normal operating conditions before using.

FCC AND IC COMPLIANCE

See this product's page at www.kleintools.com for FCC

compliance information.

Canada ICES-003 (B) / NMB-003 (B)

Do not place equipment and its accessories in the trash. Items must be properly disposed of in accordance with local regulations. Please see www.epa.gov/recycle

for additional information.

450 Bond Street, Lincolnshire, IL 60069

• Environment: Indoor

• Operating and Storage Altitude: Up to 6562 ft. (2000 m)

. The tester will emit a

• Operating Temperature: 32° to 140°F (0° to 40°C)

and green LED

in the tip

• Storage Temperature: 14° to 122°F (-10° to 50°C)

• Relative Humidity: <85% non-condensing

• Mains supply voltage uctuations: ±10%

• Nominal Voltage: 110 - 125V AC at 50/60Hz in 3-wire outlet

• Standards: Conforms to UL Std 61010-1, 61010-2-030,1436.

Certi ed to CSA Std C22.2 #61010-1, 61010-2-030,160.

5001748

Read, understand, and follow all warnings and instructions before operating testers. Failure to

follow instructions could result in death or serious injury. Before each use, verify tester operation

by testing on a known live and correctly wired receptacle. Do not use if the tester appears

damaged in any way. The tester is intended for indoor use only. Other equipment or devices

attached to the circuit being tested could interfere with the tester, clear the circuit before testing.

This tester only detects common wiring problems. Always consult a qualified electrician to resolve

wiring problems.

in the tip

Conditions indicated: wiring correct, open ground, reverse polarity, open hot, open neutral and hot/

ground reversed.

Conditions NOT indicated: quality of ground, multiple hot wires, combinations of defects, reversal of

grounded and grounding conductors.

All appliances or equipment on the circuit being tested should be unplugged to help reduce the

possibility of erroneous readings.

STANDARD RECEPTACLES

1. Verify tester operation by testing on a known live and correctly wired receptacle.

2. Plug tester into receptacle.

3. Compare the illuminated lights on the tester to the key code printed on the tester.

4. If the tester indicates that the receptacle is not wired correctly, consult a qualified electrician.

GFCI RECEPTACLES

1. Check the GFCI receptacle user manual for information on how the specific receptacle operates prior to

using this tester.

2. Insert the tester into the receptacle under test to check for correct wiring (See FIG. 1). Lights on the

tester should illuminate.

3. Press the "TEST" button on the GFCI receptacle.

Did the GFCI trip and the lights on the tester go dark?

YES: Reset the GFCI by pressing the reset button. Proceed to step 4.

NO: The GFCI is not operating properly or the receptacle is miswired. Consult a qualified electrician.

4. Press and hold the test button on the tester for 7 seconds.

Did the GFCI trip and the lights on the tester go dark?

YES: Reset the GFCI by pressing the reset button. The GFCI appears to be operating properly.

NO: The GFCI is not operating properly or the receptacle is miswired. Consult a qualified electrician.

Wipe with a clean, dry lint-free cloth. Do not use abrasive cleaners or solvents.

DISPOSAL / RECYCLE

CUSTOMER SERVICE

KLEIN TOOLS, INC.

1-800-553-4676

RT210

GENERAL SPECIFICATIONS

Specifications subject to change.

WARNINGS

WIRING CONFIGURATION TESTING

CLEANING

customerservice@kleintools.com

www.kleintools.com

• Weight: 1.2 oz (33 g)

• Pollution degree: 2

• Safety Rating: CAT II 300V

• Drop Protection: 6.6 ft. (2 m)

Klein Tools NCVT-1XTKIT Manual De Instrucciones página 2

Idiomas disponibles

Manuales relacionados para Klein Tools NCVT-1XTKIT