Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 4

HOW TO USE

1. Clean and disinfect the surface you are going to use. It is important that you wash your hands.
2. Fill the kettle with fresh tap water (do not use water that has been boiled before). Boil the water.
3. Take care when handling freshly boiled water.
Using the hot flask and
Using the cooling flask
cooling flask
4a. Add the boiled water to
4a. Fill the hot flask with
the cooling flask, using
boiling water, and
the graduation marks on
take out of the home
the inside of the flask.
with you.
4b. Measure out the
formula as per
manufacturer
instructions and store
in the milk powder
dispenser until you are
ready to use.
4c. When you are ready to
feed, attach the digital
lid to the hot flask and
tilt the flask sideways
for a minimum of 5
seconds to ensure the
water is still hot enough
and safe to make a feed.
The star on the digital
lid should turn red.
4d. You can now pour the
water from the hot flask
into the cooling flask
using the graduation
marks on the inside of
the flask for correct
measurements
5. Add the correct amount of formula powder, as per manufacturers guidelines, in line with the amount
of water in the flask.
6. Screw the digital lid onto the cooling flask, ensuring it is assembled correctly, and shake well to mix
the powder with the hot water, ensuring its fully dissolved. Shaking the cooling flask starts the cooling
process.
7. The time it takes for the feed to cool depends on the feed size, refer to the table below. To check
if a feed is ready to dispense into a baby bottle, tilt the cooling flask sideways for a minimum of
5 seconds so the milk touches the digital lid. The lid will show a blue star when the feed is ready.
Don't dispense the feed before 2 minutes
8. Decant your feed into a clean, sterile bottle. And follow bottle feeding instructions.
9. Always check the temperature before feeding your baby. Once a feed is made, use straight away.
Hot flask
Cooling flask
DIGITAL LID
The integrated thermometer in the digital lid will activate the digital
screen when it contacts water or milk. The same lid can be used to
take the temperature of milk or water when used on either the cooling
flask or the hot flask. It will tell you when a feed is ready for baby, but
also when water is still hot enough to start making a feed. Activate the
digital screen by tapping the screen.
When testing the temperature of milk
(on the cooling flask)
Blue Star
Amber Star
Red Star
Feed is too hot,
Feed is too hot,
Feed is ready
please wait
please wait
Under most circumstances the digital lid will not show a red star when attached to the
cooling flask. This is because the cooling flask will start cooling the feed immediately and
brings the feed temperature below the range that would show a red star. That is why we
recommend you test the temperature of your water before making a feed by placing the
digital lid on the hot flask to ensure the water is safe to make a feed.
COOLING TIMES
Cooling times should be used as a guide only. Always check food temperatures before
feeding. Always follow formula powder manufacturer's instructions for making a feed.
Feed size
90ml
120ml
150ml
(ml / fl oz)
3 fl oz
4 fl oz
5 fl oz
Time to cool
2m
2m
3m
(minutes)
COOLING FLASK RESET TIMES
Sterilisation /
Cold water
Electric steam
Cleaning method
Sterilisation
Sterilisation
Reset Time
3h
(hours)
The cooling flask works by absorbing heat from hot liquids. After being exposed to heat, it
will require a minimum of 3 hours before being ready to use again.
When testing the temperature of water
to make up a feed (on the hot flask)
Blue Star
Amber Star
Water is too cold
Water is too cold
Water is hot enough to make
to make a feed
to make a feed
a feed, add your formula now
180ml
210ml
240ml
6 fl oz
7 fl oz
8 fl oz
4m
5m
5m
UV
Dishwasher
Sterilisation
4h
3h
3h
Red Star

Publicidad

Tabla de contenido
loading

Tabla de contenido