Publicidad
Idiomas disponibles
Idiomas disponibles
CARDIN ELETTRONICA spa
Via del lavoro, 73 – Z.I. Cimavilla 31013 Codognè (TV) Italy
Tel:
Fax:
email (Italy):
email (Europe):
Http:
DIGITAL RADIO CONTROLS WITH ROLLING CODES S449
REMARKS
These instructions are aimed at professionally qualified "installers of electrical equipment"
and must respect the local standards and regulations in force. The use and installation of
these appliances must rigorously respect the indications supplied by the manufacturer and
the safety standards and regulations in force.
Attention! Only for EU customers - WEEE marking. This symbol indicates that
once the products life-span has expired it must be disposed of separately from
other rubbish. The user is therefore obliged to either take the product to a suitable
differential collection site for electronic and electrical goods or to send it back to
the manufacturer if the intention is to replace it with a new equivalent version of
the same product. Suitable differential collection, environmental friendly treatment
and disposal contributes to avoiding negative effects on the ambient and consequently
health as well as favouring the recycling of materials. Illicitly disposing of this product by
the owner is punishable by law and will be dealt with according to the laws and standards
of the individual member nation.
Description
The S449 Radio control system in "FM" consists of one or more transmitters and one or more
receivers which can be combined to meet the specific needs of the system. The generated code
is memorised in the receiver via radio. The receiver is able to memorise up to 300 different codes.
Important: The transmitted code changes for each command (rolling code). If disturbance
interrupts the transmission, the receiver will wait for a different code, the relay can then only be
activated by first releasing and then pressing the transmitter channel button again.
Use
The S449 radio control allows the remote activation of electrical and electronic appliances with its
best use in the following areas: automatic opening systems, alarm systems, and in all systems which
require remote control activation (without wires) using secret codes.
Transmitter versions
TXQ449100
Miniaturised transmitters
TXQ449200
Miniaturised transmitters
TXQ449300
Miniaturised transmitters
TXQ449400
Miniaturised transmitters
TXQ44940M
Wall mounted transmitter
Receiver versions
RSQ449100
Slot-in receiver card (open collector output)
Antenna
A tuned antenna using a coaxial cable RG58 (impedance 50Ω) with a maximum length of 15
m must be installed. The antenna should be positioned out of doors in the highest possible
point, visible and away from metal structures. It is good practise to position the receiver
away from computer systems, alarm systems and other possible sources of disturbance.
Transmitters
The transmitter is pre-coded and is fitted with an integrated circuit which is programmed
in the factory with a unique identification number.
All the code parameters are contained in this integrated circuit (external memory modules
are not required) thus making code management more reliable and the system more secure.
The transmitter has an automatic shut down mechanism which cuts in after at least 25
seconds of continuous use (this limits battery consumption).
• This time can vary from transmitter to transmitter.
Key block function
• A key block function has been added to protect the appliance from accidental activation;
- to activate the function press and hold down "MR" for 8 seconds until
the red led starts flashing, at this point to activate a command you will
need to press the required key three times consecutively;
- to reset the function to standard operation standard press and hold
down "MR" for 8 seconds until the red led starts flashing.
Receivers
Warning! The receivers must only be powered by a safety power pack. The use of non
safety power packs could provoke damage to the system.
The receiver cards must be sufficiently insulated from the parts of the host device which
are powered by the mains.
The slot-in receiver card with "Pin-Strip" connections must be directly inserted into the
host appliance.
The radio reception part is made up of a 433 MHz RF module "R1" inserted in the card.
The receiver has a single "open collector" output (contact 10 on the connector fig. 1).
This output can be activated by any of the transmitter channels as long as they have been
memorised in the receiver.
+39/0438.404011
+39/0438.401831
Sales.office.it@cardin.it
Sales.office@cardin.it
www.cardin.it
1 Button
2 Buttons
3 Buttons
4 Buttons
4 Buttons
1 Channel
All rights reserved. Unauthorised copying or use of the information contained in this document is punishable by law
Description :
MEMORIZZAZIONE CODICE TX-RX
Drawing number :
DM0531
Product Code :
RCQ449100
Draft :
P.J.Heath
Date :
13-04-2001
CARDIN ELETTRONICA S.p.A - 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831
SERIAL NUMBER
ZVL469.00
The S449 series conforms to the essential requirements of the directive 99/05/
CE and the technical reference standards have been applied.
Frequency validity: 433.92 MHz for all
Functions
Attention! Before memorising the transmitters for the first time remember to cancel the
entire memory content.
Memorising a channel (fig. 1)
1. Keep button "P1" MEMO pressed down and the led
"L1" will start to flash slowly
2. Press the channel on the transmitter which is to be
memorised
3. Keep button "P1" MEMO pressed down until led
"L1" starts to flash again
4. Release the button and the LED continues to flash
5. Press the channel on the transmitter which is to be memorised again (same transmitter,
same channel. If the channel or the transmitter is different you will not be able to memorise
the channel.
6. End of the memory procedure. LED "L1" will remain lit for 2 seconds meaning that the
channel has been correctly memorised.
• It is not possible to memorise a user code that is already in memory: In this case when
the transmitter is activated (point 2) the led will stop flashing. The program will only work
again when button "P1" MEMO has been released.
• If the transmitter is not activated a second time within fifteen seconds the program will
automatically leave the memory mode without memorising a new user code.
• If a new user code is activated the first time and a different channel (with an already
memorised user code) is activated the second time, the program will automatically leave
the memory mode (because the two codes do not correspond) and the channel present
in the second transmission will be activated.
Cancelling a channel (fig. 1)
1. Keep button "P2" DELETE pressed down and the led "L1" will start to flash rapidly
2. Press the channel on the transmitter which is to be cancelled
3. Led "L1" will remain lit for 2 seconds meaning that the channel has been cancelled.
Note: If the user which is to be cancelled is not found in the memory, the led will stop flash-
ing. The program will only work again when button "P2" has been released. If the button is
released before a channel is activated the program will automatically leave the memorising
or cancelling mode.
Cancelling the entire user memory (fig. 1)
1. Keep buttons (P1+P2) pressed down simultaneously for more than 4 seconds
2. Led "L1" will remain lit for the period of time required for the program to cancel all the
codes (about 8 seconds)
3. Led "L1" will turn off meaning that the cancellation procedure has been carried out.
Note: It is only possible to switch from memorising mode to cancelling mode if you haven't
already entered the second part of the memorising procedure (point 4 onwards). Once this
part of the procedure has been reached the entire procedure will have to be completed. If
you do not wish to memorise a code which you have already transmitted wait for 15 seconds,
the led will switch off and the code won't be memorised. When the receiver's memory is
almost full the user search function can take up to 1 second to complete.
Memorising a channel via radio (fig. 1, 1a, 1b)
• Memorisation can be activated by radio (without opening the receiver container) if jumper
"J1" has been inserted (fig. 1).
1. Make sure that the jumper "J1" has been inserted in receiver.
2. Using a transmitter, in which at least one channel button "A,B,C or D" has already been
memorised in the receiver, press the button "MR" as shown in figures "1a, 1b".
Note: all the receivers within range when the channel button is pressed (and which have
at least one of the transmitter channel buttons memorised) will activate their signal buzzer
"B1" (fig. 1).
3. Press one of the channel buttons on the transmitter. The receivers which do not contain
that channel code will sound a five-second long "beep" and will then disactivate.
The receivers which contain the channel code will sound a one-second long "beep" and
will enter the programming mode.
4. Press one of the channel buttons on the transmitter which you wish to memorise; the
receiver will sound 2 "beeps" of half a second each after which the receiver will be ready
to receive another code.
5. To leave the programming mode wait for 5 seconds without pressing any buttons. The
receiver will sound a five-second long "beep" and will then exit the programming mode.
• When the memory is entirely occupied the buzzer will sound 10 rapid "beeps" and will
automatically leave the "programming via radio" mode.
Led "L1" will remain lit on the receiver. The same signal is given each time you try to enter
"programming via radio" when the memory is full.
SERIES
MODEL
S449
FM
03-12-2004
countries
DEL
P2
DATE
MEMO
P1
L1
Publicidad
