Emergency Stop Light; Setup And Special Configurations - Midland BTX2 PRO Manual De Instrucciones

audio source (but not independently from the Intercom Volume). The AGC system will
automatically increase the volume on higher speed.
Attention: never set the volume of the MP3 Player to the maximum possible. Normally the
best level is about the 70% of the maximum.
Hint: We recommend that you perform a few tests adjusting the volume of your iPod/MP3
player so at the normal speed the Headset volume is suited to your needs. The AGC system
will automatically increase the volume on higher speed, so you don't need the VOL+ or VOL-
buttons to adjust it.
Enabling/disabling the wired input
If needed the wired input can be enabled or disabled:
Enabling/Disabling: Make a Long press (3 sec.) on the "Forward" and "Middle" button
(you will hear one audio beep tone for enabling confirmation and two audio beep tones
for disabling). This setting is rembered also after turning On/Off the unit.
Wired audio in background
The audio from the wired connection can be in background to your Intercom or Phone
communication. By default this option is ON. Please refer to the paragraph "Wired con-
nection always in background" below to disable it.
Note that is not possible to have the wired audio source in background to the FM radio.

Emergency Stop light

On the back of your BTX2 PRO mounting kit you have an ul-
tra bright LED emergency stop light. Every time you make a full
brake, the stop light will turn ON to give an extra alert to the
drivers behind you. In case you need to turn it OFF tempora-
rily (for example when you ride with a passenger), just press long
"Backward" and "Forward" buttons togheter while in "Phone" or
"Intercom" mode (a voice announcement will confirm the status).
The unit will remember the last setting used, that means you need
to turn ON manually the stop light pressing again "Backward" and
"Forward" buttons togheter.
Attention: By default the stop light is OFF
www.midlandeurope.com

Setup and special configurations

Resetting all paired devices
Sometimes you may find it necessary to delete all the pairing references stored in the
Midland BTX2 PRO unit (reset operation).
To perform this operation you must first enter the setup mode:
› Turn off the unit
› Press and hold down the "Middle" button about 7 sec., until the Red light is on per-
manently.
› Then simultaneously press and hold down the "Volume +" and "Volume –" buttons for
3 seconds. The Blue Light will be lit on for 1 sec and than back to steady RED.
› Double click on the "Middle" button to exit the "Setup" mode and use the Midland
BTX2 PRO.
This procedure deletes all the paired Bluetooth devices stored in the memory and it is
therefore possible to start a new "clean" pairing session.
Back to factory setting
Sometimes you may find it necessary to go back to the factory setting, to reset all the
changes/setup already made and have a "clean" unit.
To perform this operation you must first enter the setup mode:
› Turn off the unit
› Press and hold down the "Middle" button about 7 sec., until the Red light is on per-
manently.
› Then simultaneously press and hold down all the three buttons "Forward"-"Midd-
le"-"Backward" for 3 seconds. The Blue Light will be lit on for 1 sec and than back to
steady RED.
› Double click on the "Middle" button to exit the "Setup" mode and use the Midland
BTX2 PRO
Adjusting/ Disabling the VOX feature (Intercom and telephone)
The Intercom feature can be enabled both manually and vocally (VOX). The VOX activa-
tion is influenced by the helmet type, the background noise and therefore by the speed.
Stop Light
For optimum results, it is possible to choose one of the following four microphone sen-
sitivity levels: high, medium, low and very low. The default setting of Midland BTX2 PRO
is "High". It is also possible to disable the VOX feature in order to activate the Intercom
33