Publicidad
Idiomas disponibles
Idiomas disponibles
Press variable speed trigger switch (1) to start operation.
u
Release variable speed trigger switch to stop operation.
Always check torque with a torque wrench, as the
fastening torque is affected by many factors including
the following:
Voltage: Low voltage, due to a nearly discharged
u
battery, will reduce fastening torque.
Accessory size: Failure to use the correct accessory
u
size will cause a reduction in fastening torque.
Bolt size: Larger bolt diameters generally require
u
higher fastening torque. Fastening torque will also vary
according to length, grade, and torque coefficient.
Bolt: Ensure that all threads are free of rust and
u
other debris to allow proper fastening torque.
Material: The type of material and surface finish of
u
the material will affect fastening torque.
Fastening time: Longer fastening time results in
u
increased fastening torque. Using a longer fastening
time than recommended could cause the fasteners
to be overstressed, stripped or damaged.
LED work lights
The worklight (7) is activated when the trigger switch is
depressed, and will automatically turn off 20 seconds after
the trigger switch is released. If the trigger switch remains
depressed, the worklight will remain on.
Note: The worklights are for lighting the immediate work
surface and are not intended to be used as a flashlight.
Maintenance
Your STANLEY FATMAX tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
Warning! Before performing any maintenance on the tool,
remove the battery from the tool. Unplug the charger before
cleaning it.
Regularly clean the ventilation slots in your tool and
u
charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth.
u
Do not use any abrasive or solvent-based cleaner.
Regularly open the chuck and tap it to remove any dust
u
from the interior.
Protecting the environment
Z
Separate collection. Products and batteries
marked with this symbol must not be disposed
of with normal household waste.
(Original instructions)
Products and batteries contain materials that can be recov-
ered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according to
local provisions. Further information is available at
www.2helpU.com
Technical data
Voltage
No-load speed
Beats
Max. torque (PTI Method)
Anvil Size
Weight
Charger
SFMCB11
Input Voltage
V
AC
Output Voltage
V
DC
Current
A
Battery
SFMCB201
/ SB201
Voltage
18
V
DC
Capacity
Ah
1.5
Type
Li-Ion
Level of sound pressure according to EN 62841:
Sound pressure (L
) 98 dB(A), uncertainty (K) 3 dB(A)
pA
Sound power (L
) 106 dB(A), uncertainty (K) 3 dB(A)
WA
Vibration total values (triax vector sum) according to EN 62841:
Impact tightening of fasteners (a
h
Declaration of Conformity
The Supply of Machinery (Safety) Regulations 2008
Cordless Impact Wrench - SFMCF940
STANLEY FATMAX declares that these products described
under "technical data" are in compliance with:
The Supply of Machinery (Safety) Regulations, 2008, S.I.
2008/1597 (as amended), EN 62841-1:2015 + AC:2015
+A11:2022; EN62841-2-2:2014.
ENGLISH
SFMCF940
V
DC
-1
450 / 1200 / 2000
Min
BPM
Nm
inches
kg
SFMCB12 /
SC200
230
230
18
18
1.25
2
SFMCB202
SFMCB204
SFMCB206
/ SB202
/ SB204
18
18
2.0
4.0
Li-Ion
Li-Ion
2
) 14.1 m/s
, uncertainty (K) 1.5 m/s
18
0 - 2600
950
1 / 2
2.70
SFMCB14
230
18
4
18
6.0
Li-Ion
2
9
Publicidad
