Publicidad
Idiomas disponibles
Idiomas disponibles
Pictograms used
Fold out the folded page
Read instructions!
Observe warning and safety instructions!
!
Rotate object 180°
!
180 o
Telescopic insect screen for door
• Introduction
Congratulations on the purchase of your new
product. You have chosen a high quality prod-
uct. Familiarise yourself with the product before
using it for the first time. Please read the following operat-
ing instructions and the safety instructions carefully. Use the
product only as described and for the specified applications.
Keep this manual in a safe place. Hand over all documents
when passing on the product to third parties.
• Intended use
The insect screen product may be used only for its intended,
non-commercial use (installation on the existing door frame).
Misuse may cause hazards. Additional loads on this product
due to attached objects or operation beyond the mechani-
cal limitations may result in damage to the product and are
therefore not permitted. The manufacturer shall not assume
any liability for the damages resulting herefrom.
• Part description/Items supplied
[1] 2x wide telescopic profile 1435 mm
[2] 2x narrow telescopic profile 700 mm
[3] 2x wide telescopic profile 635 mm
[4] 2x narrow telescopic profile 435 mm
[5] 1x large door telescope mid rail 636 mm
[6] 2x small door telescope mid rail 250 mm
[7] 4x corner connector
[8] 4x brush clamp
[9] 4x PVC omega strip 600 mm
[10] 4x PVC fabric clip strip 1040 mm
[11] 4x PVC fabric clip strip 950 mm
12] 1x rear handle, 1x front handle
[13] 3x hinge set
[14] 2x magnetic catch, 2x counter plates
[15] 1x screw bit PH1
16] 1x drill bit Ø 3.5 mm
[17] 1x drill bit Ø 2 mm
[18] 1x drilling template
[19] 4x screw 3.5x50
[20] 18x screw 2.9x9.5
[21] 12x screw 2.9x19
[22] 3x screw 2.9x9.5
[23] 4x screw 3.5x6.5
52 | GB
Introduction/ General safety instructions
Two people needed
Do not expose fibreglass fabric or any plastic parts
to open flames or any other source of heat.
Products and packaging should be disposed of in
an environmentally friendly manner.
Recycling code for cardboard disposal
20
PAP
[24] 4x screw 2.9x9.5
[25] 2x aluminium junction plate
[26] 1x high brush seal
[27] 1x low brush seal
[28] 1x mesh
[A] 1x adhesive strip
[B] 1x, screw bit PH2
Safety instructions
Please read the instructions carefully before assem-
bly! Keep the instructions and hand them over when
!
passing on the product!
Do not expose fibreglass fabric or any plastic parts
to open flames or any other source of heat.
CAUTION! RISK OF INJURY!
Be careful when using the cutter knife.
•
Assembly
CAUTION! Risk of damage to the product! When assembling,
place a blanket or something similar underneath to
!
prevent scratches.
Fig. 1:
•
First measure the inside dimensions of the door (X = width,
Y = height).
•
Open the door to do this (see Fig. 1)
•
Enter the dimensions in the fields provided.
Fig. 2:
•
Connect the four corner connectors [7] 2x to the profiles
[1] and [4] and 2x to the profiles [2] and [3]. Use a rubber
mallet to drive the corner connectors [7] into the profiles.
Fig. 3:
•
Slide a narrow profile [2] into a wide profile [1] and a nar-
row profile [4] into a wide profile [3] to create a rectangu-
lar frame. CAUTION! There should be a minimum pro-
jection of 20 mm on the left and right of the door frame
for installing it, as hinges and magnetic catches will be
screwed on later.
Fig. 4:
•
Telescope the frame to the width and height dimensions X
and Y (Fig.1). Extend each of these by 30 mm.
Fig. 5:
•
(a) Measure the length of the still visible profiles A [4] and
B [2] and enter the dimensions.
Publicidad
