Publicidad
Idiomas disponibles
Idiomas disponibles
Assembly
•
(b) Mark 2x length A and 2x length B on the omega
strips [9].
•
(c) Cut the omega strips [9] 2x to length A and 2x to
length B.
Fig. 6:
•
Mount the cut omega strips [9] on profiles A [4] and pro-
files B [1] on the projection inside the frame (see mag-
nifying glass).
Fig. 7:
•
Turn the frame 180° so that the outside of the door is
on top.
•
Push the profiles back together to the dimension spec-
ified with the omega strips if the profiles have shifted
when they were turned over.
Fig. 8:
•
Calculate the height C = Frame height D : 2
•
Place the drilling template [18] on the vertical sides of
the frame centred at height C and fix it with adhesive
tape [A].
•
(a) Drill the holes in field 1 on the outside of the frame
using the 3.5 mm drill bit [16]. CAUTION! Only drill
through the outer wall of the profile, not the entire pro-
file!
•
(b) Drill the holes in field 2 on the inside of
the
frame
using
CAUTION! Only drill through the outer wall of the pro-
file, not the entire profile!
Fig. 9:
•
(a) Screw a narrow profile [6] with the outside facing
upwards with the enclosed bit [B] on one side to the pre-
drilled holes with a 2x screw [19].
•
(b) Slide the wide profile [5] over the narrow profile [6].
Fig. 10:
•
(a) Screw a narrow profile [6] with the outside facing
upwards with the enclosed bit [B] on the opposite side to
the pre-drilled holes with 2x screw [19].
•
(b) Slide the wide profile [5] over both narrow profiles [6]
so that it is centred.
Fig. 11/24:
•
(a) Place drilling template [18] on the profile on the door
stop side at the top directly under the corner connector,
in the middle directly under the centre bar and at the
bottom directly above the corner connector, fasten with
adhesive tape [A] and either drill in field 3 if the template
is on the wide profile [2] or drill in field 4 if the template
is on the narrow profile [1]. With the narrow profile, care
must be taken that the holes in the side of the template
do not cover the profile. CAUTION! Only drill through
the outer wall of the profile, not the entire profile!
Fig. 12/25:
•
Screw the upper part of each door hinge [13] to the pre-
drilled holes using the enclosed bit [15] and 2 screws
[21] each.
Fig. 13/26:
•
On the side facing away from the hinges, measure 715
mm downwards from the top edge of the top corner
connector and 715 mm upwards from the bottom edge
of the bottom corner connector. Place the drilling tem-
plate [18] there with the side holes facing outwards.
•
Drill the two screw holes with the 2 mm drill [17] in field
the
3.5
mm
drill
bit
5. CAUTION! Only drill through the external wall of the
profile, not the whole profile.
Fig. 14/27:
•
Screw the 2 magnetic snaps [14] with the enclosed bit [15]
and 2 screws [24] each to the pre-drilled holes.
Fig. 15/28:
•
Turn the frame 180° so that the inside is on top.
•
(a) Measure the visible length of the narrow pro-
files [6] (length A) at the centre bar. Enter these.
CAUTION! Profile [5] must be positioned exactly centrally
between the profiles [6]!
•
(b) Mark length A 4x on the omega strips [9]
•
(c) Cut the omega strips [9] 4x to length A
•
(d) Press 2 omega strips [9] per profile [6] firmly on the
top and bottom of the raised parts (see magnifying glass).
Fig. 16/29:
•
(a) Push the closed half of the handle into the upper corner
of the lower panel facing the magnetic snaps.
•
(b) Cut the clip strip [11] 4x to the length of the vertical
profiles measured from the inside of the corner connector
(see magnifying glass) to the middle of the centre strip. Cut
the clip strip [10] 4x to the length of the horizontal profiles
measured from the respective end of the corner connec-
tors. Leave room for the handle.
[16].
•
(c) Remove the handle again.
Fig. 17/30:
•
Unroll the fabric [28] on the frame. Cut it at the level of the
centre bar with scissors. CAUTION! Leave at least 2.5 cm
space above and below the frame!
Fig. 18/31:
•
(1) Firmly insert the closed door handle in the lower field
in the upper corner facing the magnetic snaps. Place the
open counterpart opposite this, on the outside of the door.
Screw the two parts together with the enclosed bit [15] and
3x screws [22].
•
(2) Tap the clip strips [11] on the vertical profiles and the
clip strips [10] on the horizontal profiles over the fabric on
the inside overhang of the profiles (see magnifying glass)
with a rubber mallet, following the sequence 2a-2h.
(3) Cut off the protruding fabric with a cutter knife. CAU-
•
TION! RISK OF INJURY! Be careful when using the cut-
ter knife.
Fig. 19/32:
•
Place the bracing plates [25] in the top and bottom corners
on the hinge side of the door to fit snugly on the clip strips.
Pre-drill the 4 holes with the 2 mm drill [17]. CAUTION!
Only drill through the outer wall of the profile, not the
entire profile!
•
Screw the bracing plates to the profiles with the enclosed
bit [15] and 4 screws [20] each.
Fig. 20/33:
•
(a) Cut the high brush seal [26] to the respective length
of the narrow profiles [2] and [4] and the low brush seal
[27] to the respective length of the wide profiles [1] and [3],
including corner connectors.
•
(b,c) Insert the brushes via the corner connectors into the
brush channel of the associated profiles.
•
(d) Place the brush clamps [8] in the corner connectors
over the brushes so that the spreaders face outwards.
•
(e) Screw the brush clamps [8] tight with one screw [23]
GB | 53
Publicidad
