Kinderkraft TRIG 2 Manual De Usuario página 17

• Check that the pram body or seat unit or car seat attachment
devices are correctly engaged before use
• This product is not suitable for running or skating
•
Age and weight usage: from 0 months up to 22 kg or up to 4 years, whichever comes first.
•
We recommend using lowest reclined position for newborn babies.
•
This product may only be used by one child at the same time
•
The parking device shall be engaged when placing and removing the children
•
The maximum basket load is 2 kg.
•
Maximum weight of a bag attached to the adjustable handle is 1 kg.
•
Maximum weight of cup holder: 0,5 kg.
•
Any additional load suspended from the buggy handles, backrest and sides will cause stability loss.
•
Use only parts and accessories supplied or recommended by the manufacturer. Do not use other parts or accessories.
•
Lift the front suspension when going up a curb or step.
•
Do not place the product near open flame or other heat sources.
•
Do not use with an additional platform.
B. ASSEMBLY
I. BUGGY COMPONENTS (FIG. 1)
A. Frame with seat and safety straps
B. Front wheels
C. Rear wheels
D. Safety bar
II. UNFOLDING BUGGY FRAME Place the frame on a flat surface with its handle up (FIG. 2). In order to unfold the frame,
move the lock (A) on the right side of the buggy and lift the frame up, until you hear the locking sound.
A properly unfolded frame is shown in FIG. 3.
III. WHEEL ASSEMBLY/DISASSEMBLY Put the rear wheel on the protruding part of the rear axle (FIG. 4). Clip in the metal
pin (E1) onto the axis, insert the cotter pin (E2), and at the end, cover with the plug (E3). Each of the elements should be
pressed with a slight resistance, until it locks into place. Repeat these steps on the other side of the buggy. To mount the
rear axle with the brake, put the rear free tips of the frame in the slots in the rear axle until you hear the lock click (FIG. 5).
Make sure to properly protect them with snap fasteners.
Insert the front wheels in the front axles until you hear the locking sound (FIG. 6). To remove the front wheels, push the
quick release button located below the footrest under each wheel (FIG. A). The buggy has a system of swivel front wheels
which can be locked in the straight-ahead position. To lock the wheel to move forward, slide the ring located above the
wheel (FIG. B).
NOTE! Before using the buggy, make sure that all the wheels are
properly installed.
IV. ASSEMBLY / DISASSEMBLY OF THE SAFETY STICK / TRAY. The sketches show the assembly of only one of the
elements: D / I. The method of assembly / disassembly for both of these elements is the same. The safety bar/tray must
be inserted in appropriate slots on both sides of the frame, as shown in Figure 7. To remove the part, press the release
buttons on both sides and remove the tray / safety bar (FIG. 8).
V. USE OF BRAKE The buggy is equipped with a foot brake located on the rear axle. Press the lower part of the brake
down; the brake is activated when you hear the locking sound (FIG. 9). Unlocking occurs after lifting the lower part of
brake lever.
VI. BACK AND FOOTREST ADJUSTMENT AND CUP HOLDER ASSEMBLY (FIG. 10) The footrest has 4 positions. Hold down
the buttons on both sides (FIG. A), to change the position of the footrest.
The seat is equipped with smooth backrest adjustment system, from a lying to a sitting position, using a clasp (FIG. B).
Cup holder is mounted on the left side of the buggy on the stem fixed to the frame (FIG. 11).
VII. SAFETY STRAPS (FIG. 12) The buggy's straps are adapted in such a way to enable its use even by newborns. Always use
the fastening system. To secure the child, connect the fasteners of hip and shoulder straps (FIG. A) and then insert them
into the middle buckle, until it engages (FIG. B). Adjust the straps each time.
E. Rear axle with brake / Set of wheel
fasteners
1. Pin x2
2. Cotter pin x2
3. Plug x2
F. Cup holder
I. Tray