Krups XP2280 Manual De Instrucciones página 45

English Français
ESPRESSO
TIPS
n For an intensely aromatic espresso, we recommend that you use freshly ground special espresso
coffee which is ideal for preparing this type of delicate beverage, as well as cups with a capacity not
exceeding 50 ml.
n Keep the ground coffee in the refrigerator to preserve its aroma longer.
n Do not fill your filter holder to the brim, but use the measuring spoon (1 cup = 1 spoon –2 cups =
2 spoons) (Fig. 5).
n If you do not use the appliance for more than 5 days, rinse and drain the water tank.
n Always remember to turn off the appliance before removing the tank to fill or empty it.
n Make sure you always place the appliance on a flat stable surface.
n To obtain an espresso at exactly the right temperature, we recommend that you preheat your cups.
n To prolong the service life of your appliance, we recommend that you always use a Claris Aqua Filter
System cartridge (reference: F088) and that you descale the appliance at regular intervals.
IMPORTANT!
Before using for the first use, after a prolonged period of inactivity or after desca-
ling, the appliance must be cleaned as described in paragraph 1: "BEFORE FIRST
USE".
1. BEFORE FIRST USE
Before using your espresso machine, clean all the accessories in soapy water and dry them.
A. SETTING THE TIME (to be done on first use and after a power cut)
n Your XP2280 combo machine has a display making it easy to use and providing a wide range of
settings.
n You must set the clock when you plug in your appliance for the first time or after a power cut.
n You can set the clock to 24 hour or AM-PM display mode.
n To do this, simultaneously press the "H" and "m" buttons below the display.
n Then set the hours by pressing the "H" button and the minutes by pressing the "m" button.
Make sure the steam knob on the left of the appliance is in 0 position.
If you are not using the Claris cartridge, go directly to paragraph "C. RINSING YOUR
APPLIANCE".
B. INSTALLING THE CLARIS CARTRIDGE (to be done every time the cartridge is replaced)
n Screw the Claris cartridge into the bottom of the tank.
n Fill the tank with water (Fig. 2).
n Replace the tank by positioning it firmly to ensure that water can enter and then close the lid (Fig.
3).
n Place a container under the steam nozzle.
n Turn on the appliance by pressing the Espresso
n As soon as the appliance reaches the right temperature, the
pictograms and are displayed.
n Turn the knob on the side of the appliance to
n At the start, steam will come out through the steam nozzle and the four pictograms in the display and
Espresso
the LED will begin to flash.
n Turn the knob to "0" position (fig.15).
n Turn off the machine and then turn it on again by pressing the
82
button (fig.4).
Espresso
LED glows steadily and the
(fig.13).
Espresso button twice.
n Return to knob to : position: water flows out of the steam nozzle. If water does not flow from the
nozzle, repeat the operation from the start 1 or 2 times.
n _- Turn the knob to "0" position.
In this manner you can be sure that water is circulating well through the filter cartridge.
IMPORTANT:
This installation procedure must be carried out every time the cartridge is
replaced.
The Claris cartridge needs to be replaced every 2 to 3 months if it is used daily.
C. RINSING YOUR APPLIANCE (to be done on first use and after each cleaning /
descaling operation)
- RINSING OUT THE ESPRESSO CIRCUIT
Then rinse the appliance. To do so:
n Turn on the appliance and fill the water tank (Fig. 1, 2, 3 & 4).
n Insert the filter holder (without ground coffee) in the appliance (Fig. 7).
n Place a container of sufficient volume under the filter holder.
n As soon as the appliance reaches the right temperature, the
pictograms and are displayed.
n Press the button and let the water run out into the container (fig.9).
n Repeat this operation 5 times.
n If necessary, stop the operation by pressing the
the operation (fig.9).
n Empty the container and unlock the filter holder: press the "OPEN" button on the filter holder and
turn it to the left (fig.10).
- RINSING OUT THE STEAM CIRCUIT.
Before using the steam function for the first time, the steam circuit should be cleaned.
n Fill the water tank. Make sure that the steam function dial is in O position.
Espresso
n Turn the appliance on by pressing the button.
n Place a container underneath the steam nozzle.
n When the Espresso light indicator glows, press the
on the display will begin to blink.
n When they have stopped blinking, turn the dial to the
steam is generated.
n Keep the steam production going for at least 30 seconds.
2 . MAKING AN ESPRESSO
Before making an espresso, make sure the steam knob on the left of the appliance is in 0
position.
In order to release all the aromas of the coffee and ensure your complete satisfaction, this machine pre-
brews each coffee. The pump works for 3 seconds, stops the following 3 seconds and then the cycle
continues until the end of the preparation.
PREHEATING THE ACCESSORIES
n For best results, we recommend that you first pre-heat the accessories (filter holder and cups)
without ground coffee. To do this:
n Fill the water tank and turn on the appliance (Fig. 1, 2, 3 and 4).
n Put the filter holder in place and place the cups underneath.
n As soon as the appliance reaches the right temperature, the
pictograms and are displayed.
Français English English
Espresso
LED glows steadily and the
button to empty the container and then resume
button: the Espresso light indicator and the pictogram
position and allow the water to flow until
Espresso LED glows steadily and the
83