Bosch GCM 12 GDL Professional Manual Original página 36

36 | English
Technical Data
Sliding Mitre Saw
Article number
Rated power input
No-load speed
Reduced starting current
Laser type
Laser class
Weight according to EPTA-Procedure 01/2003
Protection class
Permissible workpiece dimensions (maximum/minimum) see page 41.
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
Dimension of suitable saw blades
Saw blade diameter
Blade body thickness
Mounting hole diameter
Noise/Vibration Information
Sound emission values determined according to
EN 61029-2-9.
Typically the A-weighted noise levels of the product are:
Sound pressure level 93 dB(A); Sound power level
106 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 61029:
2 2
a <2.5 m/s , K=1.5 m/s .
h
The vibration emission level given in this information sheet
has been measured in accordance with a standardised test
given in EN 61029 and may be used to compare one tool with
another. It may be used for a preliminary assessment of expo-
sure.
The declared vibration emission level represents the main
applications of the tool. However if the tool is used for differ-
ent applications, with different accessories or poorly main-
tained, the vibration emission may differ. This may signifi-
cantly increase the exposure level over the total working
period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
1 609 92A 0XN | (13.10.14)
3 601 M23 600
3 601 M23 630
3 601 M23 670
W
-1
min
nm
mW
kg
Declaration of Conformity
We declare under our sole responsibility that the product de-
mm 305
scribed under "Technical Data" is in conformity with all rele-
mm 1.7–2.6
vant provisions of the directives 2011/65/EU, 2014/30/EU,
mm 30
2006/42/EC including their amendments and complies with
the following standards:
EN 61029-1, EN 61029-2-9, EN 60825-1.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
70764 Leinfelden-Echterdingen, GERMANY
Henk Becker
Executive Vice President
Engineering
Robert Bosch GmbH, Power Tools Division
70764 Leinfelden-Echterdingen, GERMANY
Leinfelden, 20.08.2014
Assembly
 Avoid unintentional starting of the machine. During as-
sembly and for all work on the machine, the power plug
must not be connected to the mains supply.
Delivery Scope
Carefully remove all parts included in the delivery from their
packaging.
Remove all packaging material from the machine and the ac-
cessories provided.
Before starting the operation of the machine for the first time,
check if all parts listed below have been supplied:
– Sliding mitre saw with mounted saw blade
– Locking knob 15
– Dust bag 1
– Hex key 20
– Hex key 21 (below laser protection cap 27)
– Material clamp 22
3 601 M23 660
2000 1500
3800 3800
 
635 635
< 1 < 1
2 2
32.1 32.1
/II /II
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
GCM 12 GDL
3 601 M23 690
3 601 M23 6P0
1800
3800

635
< 1
2
32.1
/II
Bosch Power Tools