Arktic 233689 Manual Del Usuario página 10

Note:
GB
• If no button is pressed within 10 seconds. The newly set tem-
perature will be stored.
• The temperature setting range from -24°C to -20°C. The ac-
tual temperature inside the appliance can be affected by the
ambient temperature.
• Keep the door open time as short as possible in order to keep
a cool temperature inside.
2). Defrost function
• Press and hold the Light ON/ OFF button (11) for about 6 sec-
onds to start/stop defrost.
3). Refrigerant LED indicator (7)
• During the cooling operation (compressor enabled), this re-
frigerant LED indicator will lights up constantly.
• After the inside cabinet reach the set temperature, the refrig-
erant LED indicator will flashes continuously.
• When defrost start, the refrigerant LED indicator light off.
4). Defrost LED indicator (8)
• During the defrost operation, this defrost LED indicator will
lights up constantly.
• After the defrost operation, defrost LED indicator will lights
off.
Cleaning & maintenance
• ATTENTION! Always disconnect the appliance from the pow-
er supply and cool down before storage, cleaning & mainte-
nance.
• Do not use water jet or steam cleaner for cleaning and do not
push the appliance under the water as the parts will get wet
and electric shock might be resulted.
• If the appliance is not kept in a good state of cleanliness, this
can adversely affect the life of the appliance and result in a
dangerous situation.
• Food residues should be regularly cleaned and removed from
the appliance. If the appliance is not cleaned properly, it will
reduce its lifespan and may result in a dangerous condition
during use.
Cleaning
• Clean the cooled exterior surface with a cloth or sponge
slightly dampened with a mild soap solution.
• For reasons of hygiene, the appliance should be cleaned be-
fore and after use.
• Avoid water contacting the electrical components.
• Never immerse the appliance in water or other liquids.
• Never use aggressive cleaning agents, abrasive sponges, or
cleaning agents containing chlorine. Do not use steel wool,
metallic utensils, or any sharp or pointed objects for cleaning.
Do not use petrol or solvents!
• No parts are dishwasher safe.
10
Parts How to clean
Adaptor • Soak in warm, soapy water for
bars and GN about 10 to 20 minutes.
containers • Rinse under running water
thoroughly.
External • Wipe clean with a soft cloth and
glass a little neutral detergent. Make
surfaces sure no water or moisture en-
ters inside the of the appliance.
Interior glass • Remove any food deposits.
surfaces • Wipe clean with a soft cloth and
a little mild detergent. Make
Glass door
sure no water or moisture en-
ters inside the of the appliance.
Maintenance
• Check the operation of the appliance regularly to prevent se-
rious accidents.
• If you see that the appliance is not working properly or that
there is a problem, stop using it, switch it off and contact the
supplier.
• All maintenance, installation and repair work must be car-
ried out by specialised and authorised technicians, or recom-
mended by the manufacturer.
Transportation and Storage
• Before storage, always make sure that the appliance has
been disconnected from the power supply and completely
cooled down.
• Store the appliance in a cool, clean and dry place.
• Never place heavy objects on the appliance as this could
damage it.
• Do not move the appliance while it is under operation. Dis-
connect the appliance from power supply when moving and
hold it at the bottom.
Troubleshooting
If the appliance does not function properly, please check the
below table for the solution. If you are still unable to solve the
problem, please contact the supplier/service provider.
Problems Possible cause
The appliance Thermal cut-out
activated
does not
start cooling
The compressor is
after connect to
defective.
electrical power
supply.
The power plug/inlet
is not connected
properly with the
power supply.
Remark
Dry all
parts well
at last.
Possible solution
Contact the supplier.
Check the connec-
tion and make sure
all the connections
are correctly con-
nected.