Kobra K245TS Instrucciones De Manejo página 10

Вы всегда можете купить это оборудование на сайте
SHREDDING CD/DVD/CREDIT CARDS
Insert the optical media into the throat of the machine (2A),the
light bar (P) comes on and the machine starts up automatically
thanks to the electronic eyes located on the inside of the throat
(2A) which detect the presence of material to be shredded and
automatically stop the cutting blades a few seconds after
shredding is finished.
The machine is fitted with a special bin (12) or (12A) for
collecting the particles of CD/DVD/CREDIT CARDS and
separates them in order to allow for separate waste disposal.
In all models KOBRA 245TS capable to shred optical media,
CDs,DVDs and Credit Cards should be inserted into the paper
feed opening.
AUTOMATIC FUNCTIONS
All models KOBRA 245/260/270/310TS come equipped with the
following automatic functions.
PHOTO CELLS (3) or (3A) to start up the machine
o
automatically as soon as any sheets of paper or optical
media are inserted into the throat of the machine (2) or
(2A).
AUTOMATIC STOP when bag is full or door is open
o
signalled by illuminated optical indicator (9) or (10) on
control panel.
MOTOR SAVE which stops the machine working if it
o
overheats.(If the motor saver comes on,the machine rests
for at least 10/15 minutes after which time the device
restarts automatically).
AUTOMATIC RETURN anti-jam system in case of
o
accidental insertion of paper in axcess of the maximum
capacity of the model,cuts off power to the motor and then
puts the machine into reverse for a few seconds in order to
free the cutting rollers.
ENERGY SMART SYSTEM once 8 seconds have passed
o
since the last shredding,the machine goes on automatic
STAND-BY with zero power consumption as indicated by
the light (1) on the control panel.After four hours of not
being used,the machine automatically shuts down the
mains power supply.
CARE AND MAINTENANCE
The shredders in the KOBRA 260/270/310TS range need no
special maintenance.However it is recommended to oil the
cutting knives with the KOBRA oil supplied with the machine as
soon as the warning light (5) comes on to ensure efficient
shredding and prolong the life of the cutting blades.
( KOBRA 245TS/260TS)
Cutting knives should be lubricated every 15 minutes of
operation to maintain rated cutting capacity.
WARNING! NEVER INSERT SHEETS SPRAYED WITH OIL
INTO THE AUTOMATIC FEEDER.
ACCESSORIES
AUTOMATIC OILER
The shredders in the KOBRA 245TS ,260TS,KOBRA 270TS
and KOBRA 310TS particle cut and HS High Security series can
be fitted on request with a special built-in AUTOMATIC OILER
system (which come as standard on the KOBRA 310TS HS)
eliminating the need for manual oiling of cutting knives.
Models fitted with the AUTOMATIC OILER are delivered
together with a 1 Litre oil container.
INSTALLATION (FIG.4)
When the machine has been taken out of the packaging, position
the machine head on the cabinet, insert the pipe (17) into the
connector (14). Take the oil container supplied with the machine,
unscrew the seal cap and discard, insert the oil pipe (13) and
tighten the cap completely (16).
OPERATION
Once the machine has been pluggen in to the mains power
supply,press the ON/OFF button (O),the light bar(P) comes on
and the machine is ready to use.
For the first few minutes,the warning light (5) fig.3 might be
flashing because the oil feeder pipe is not yet completely full.to
speed up the process and switch off the OIL warning light (5) run
the machine empty for 3 or 4 minutes by keeping the FORWARD
button (7) fig.3 pressed down.Now your shredder is ready with
oiled cutting blades.
The OIL warning light (5) fig.3 flashes to warn that there is no oil
the container.
REPLACING OIL CONTAINER FIG.4
Open the lid.
Remove the empty oil container (15) from its housing,unscrew
the lid (16) on the top of the container and remove the oil hose
(13).
Provide yourself with a new oil container,unscrew the seal and
dispose of it,insert the oil hose and tighten the lid (16).Replace
the new oil container (15) in its housing and close the lid.Now
your document shredder is ready for use again with oiled cutting
blades.
WARNING!! For the first few minutes,the warning light (5) fig.3
might be flashing because the oil feeder pipe is not yet
completely full.To speed up the process you can activate the
electronic eyes (3) or (3A) and run the machine empty for at
least 3 or 4 minutes at a strtch or else keep the FORWARD
button (7) pressed down.
NEVER use synthetic oil, benzene based products or aerosol
lubricants of any kind inside or near the machine.
Fire hazard.
10
www.office-world.ru 8 800 775-37-18