Publicidad
Idiomas disponibles
Idiomas disponibles
7. List of contents
1. Provided uses of the machine
2. Unpackaging and assembling
3. Setting or fastening the machine in a stable position
4. Connection to the grid, wiring, fuses, socket type for the
jack and grounding conditions
5. Illustrated descriptions of functions
6. Limitations regarding environmental conditions
7. List of contents
8. Settings and testing
9. Changing tools
10. Fixing the workpiece
11. Limits regarding the workpiece size
12. General instructions for use
13. Dust extraction
14. Regular cleaning, maintenance and greasing.
15. Warrantee.
16. Disposal.
17. Technical specifications
18. Declaration of conformity
8. Settings and testing
Warning!
Before any intervention on the electrical tool remove jack
from power socket.
If the machine has been subject to prolonged or intense
use, it must be checked and adjusted so as to ensure the
machine's correct quality of service and safety.
This requires knowledge, experience and special tools.
The official technical service of Stayer Iberica S.A. will ca-
rry out that work for you in a quick thorough and inexpen-
sive manner.
Adjusting the locking in the lower resting position
Verification
1. Rise the head pushing button 2.
2. Lower the head until it stops.
3. Press button 4. If it is well adjusted, the bolt of the bu-
tton should smoothly enter up to the stop. If not, proceed
to adjust it.
Adjustment
1. Loosen the fastening screw of the locking screw 5.
2. Lower the head to the lower stop.
3. Tighten or loosen screw 5 until the knob 4 penetrates
the stop smoothly.
4. While the screw is held, tighten the nut of the perpen-
dicular restraint.
Adjust the angle of the horizontal mitre joint to
+- 45º
Verification
1. Move the head horizontally until it is locked at +45º.
2. Verify that the horizontal angle indicator marks exactly
45º. If not, proceed to the adjustment.
3. Repeat the same sequence for the horizontal angle at
-45º.
ENGLISH
10
Adjust the vertical mitre joint angle to 90º and 45º.
Verification
1. Release the vertical adjustment of the head by loose-
ning 8.
2. Move the head to the left stop (+45º) or central stop
(90º). Use 8 to release +45
3. Check the angle by means of a duly calibrated angular
template or a compass (minimum precision +-5') presen-
ting one of its surfaces on the lower table and the other
on the cutting disc. Use light as contrast to see the ad-
justment.
9. Tool change
Warning!
It is mandatory to use discs according to EN 847-1 STAYER
originals.
Cambio del disco de corte
1. Lift the disc guard lowering the head.
2. Hold the disc by pressing it against a wooden chuck
and loosen the disc screw spinning it to the right.
3. Extract the disc from above and install the new one fo-
llowing the two previous sections in reverse order.
10. Fixing the workpiece
Whenever possible, the workpiece must be fixed in such a
manner that the hand does not intervene. During the cut,
keep the workpiece fixed to the support.
While cutting the piece must be steadily held.
MANDATORY CLAMP USE.
To avoid deformations of the workpieces during fixing the-
reof, the use of wooden profiles being easily applicable to
the movable jaws of the clamps is advised. Clamps can
be installed on 7
For cutting long workpieces under safe conditions it is es-
sential to hold them with additional supports located in the
6, once placed fix them with the screws under the table.
11. Limits regarding the workpiece size
Limits as included in the present manual. Pag. 4.
12. General instructions for use
Warning!
1. Do NOT use the machine if it is in a bad condition, or
lacks parts including the prescribed upper guards (the
illustrations of the present manual may be used as an
orientative guide). Unplug it, remove it from the working
area and immediately send it to an authorized technical
service.
2. Know and comply with all safety measures before you
start the machine.
10
Publicidad
