Descargar Imprimir esta página

RIDGID R8641 Manual Del Operador página 68

Publicidad

OPERATION
WARNING:
Do not allow familiarity with products to make you
careless. Remember that a careless fraction of a
second is sufficient to inflict serious injury.
WARNING:
Always wear eye protection with side shields
marked to comply with ANSI Z87.1. Failure to do
so could result in objects being thrown into your
eyes resulting in possible serious injury.
WARNING:
Do not use any attachments or accessories not
recommended by the manufacturer of this product.
The use of attachments or accessories not
recommended can result in serious personal injury.
APPLICATIONS
You may use this product for the following purposes:
 Charging 9.6 V, 12 V, 14.4 V, and 18 V RIDGID nickel-
cadmium battery packs
 Charging 18 V RIDGID Lithium-ion battery packs
CAUTION:
If at any point during the charging process none
of the LEDs are lit, remove the battery pack from
the charger to avoid damaging the product. DO
NOT insert another battery. Return the charger and
battery to your nearest service center for service
or replacement.
CAUTION:
Charge in a well ventilated area. Do not block
charger vents. Keep them clear to allow proper
ventilation.
USE THIS RIDGID BATTERY CHARGER ONLY WITH
THE BATTERY PACKS LISTED BELOW.
Part Number
Voltage
130252007
9.6
130252002
12
130254001
12
 For use with 18 V nickel-cadmium and 18 V lithium-ion
battery packs, see tool/appliance/battery pack/charger
correlation supplement 988000-302 or 988000-378.
Part Number
Voltage
130252003
14.4
130254002
14.4
130254008
14.4
6 — English
CHARGING
See Figure 2, page 10.
Battery packs are shipped in a low charge condition to
prevent possible problems. Therefore, you should charge
them before first use.
If the charger does not charge your battery pack under
normal circumstances, return both the battery pack and
charger to your nearest repair center for electrical check.
For the location of your nearest repair center, please call
1-866-539-1710.
 Make sure the power supply is normal household voltage,
120 volts, AC only, 60 Hz.
 Connect the charger to a power supply.
 Attach the battery pack to the charger by aligning the
raised ribs on the battery pack with the grooves in the
charger, then slide the battery pack onto the charger.
 Press down on the battery pack to be sure contacts on
the battery pack engage properly with contacts in the
charger.
NOTE: The 9.6 V, 12 V, and 14.4 V battery packs will not
slide all the way down onto the charger port.
 Do not place the charger in an area of extreme heat or
cold. It will work best at normal room temperature.
NOTE: The charger and battery pack should be placed
in a location where the temperature is more than 50°F
but less than 96°F.
 The battery pack will become slightly warm to the
touch while charging. This is normal and does not
indicate a problem.
 After charging is complete, the green LEDs will remain
on while the charger is in Maintenance mode.
 After completing Maintenance mode, the green LEDs
will begin fading on/off continuously. This indicates the
battery is fully charged and the charger is in Energy Save
mode.
 Charger will periodically wake from Energy Save mode to
ensure the battery pack remains in a fully charged state.
 To remove the battery pack from the charger, pull up on
the battery pack.
CHARGING A HOT BATTERY PACK
When using the tool continuously, the battery pack will become
hot. A hot battery pack may be placed directly onto the charger
port. When placed on the charger, a hot battery pack will not
attempt to recharge until it cools to a proper temperature.
If the battery pack is above normal temperature range, the
Temperature LED will begin fading. When the battery pack
cools down to approximately 120°F (40°C), the charger will
automatically begin fast charge mode.
CHARGING A COOL BATTERY PACK
If the battery pack is below normal temperature range,
the Temperature LED will begin fading. When the battery
warms to a temperature of more than 32°F, the charger will
automatically begin fast charge mode.

Publicidad

loading