Clarke 56383986 Instrucciones De Uso página 8

página de 76

/ 76
Marcadores

Idiomas disponibles

ENGLISH

MACHINE CONTROL PANEL

Clarke

Key Switch (See Figure 1, Item "A")

The key switch turns "ON" the power to the control panel. "O" is "OFF" and "I" is "ON". Model 56383986 uses a rocker switch to turn machine ON

and OFF.

Traverse Speed Switch (See Figure #1, Item "B")

The speed control varies from low to high speed. To increase the speed, turn the knob to the right. To decrease the speed, turn the knob to the left.

One Touch Control Button (See Figure 1, Item "C")

The one touch control button raises and lowers the brush head assembly, starts and stops the vacuum motor automatically. Press the one touch

control button once and the brush head assembly lowers to the ﬂ oor and the vacuum motor turns "ON" (brush head and vacuum LEDs illuminate

green). The brush motors start when the brushes are down and the forward palm button is depressed (both left and right must be pressed at the

same time for model 56383986). Press the one touch control button again and the brush head assembly raises, the vacuum motor will remain on for

10 seconds and then shut "OFF".

Increase Brush Pressure Button (BOOST and Disk only) (See Figure 1, Item D)

This button is used to increase the brush pressure. Increased brush pressure may be required when stripping or cleaning heavily soiled ﬂ oors. To

increase brush pressure, ﬁ rst lower the brushes by pressing the one touch control button (Item "C"). This will lower the brushes to the normal scrub

position. To increase brush pressure, press the button (Item "D"). The LED above the button will illuminate yellow. Press the button (Item "D") again

and the brushes will return to normal scrub (yellow LED will turn "OFF"). NOTE: Increase brush pressure is not available on cylindrical machine.

Vacuum Motor Button (See Figure 1, Item "E")

The vacuum motor button turns the vacuum motor "ON" or "OFF", regardless of brush head assembly position. The green LED will illuminate when

the vacuum motor is "ON".

Solution Control Buttons (See Figure 1, Item "F & G")

The solution control buttons regulate the ﬂ ow of cleaning solution to the ﬂ oor. The normal scrub solution setting is indicated by two green bars on the

meter. On cylindrical machines, with most ﬂ oor conditions, the solution setting should be set one step higher. To increase the ﬂ ow, press the solu-

tion ﬂ ow button "G" (+) until the desired ﬂ ow is reached. To decrease the ﬂ ow, press the solution ﬂ ow button "F" (-) until the desired ﬂ ow is reached.

To shut off the solution, press the solution ﬂ ow button "F" (-) until no indicators are visible on the display. NOTE: No solution will ﬂ ow when the

machine does not traverse.

Forward Palm Buttons (See Figure 1, Item "H")

The forward palm buttons turn the traverse motor "ON" and if the brush motors are in the down position, it also activates the brush motors and solu-

tion control module. Either the right or the left palm button can be used (both left and right must be pressed at the same time for model 56383986).

Reverse Push Button (See Figure 1, Item "I")

The reverse push button, when used in conjunction with one of the forward palm buttons (both palm buttons for model 56383986), causes the

machine to reverse direction. The reverse speed is 67% of the forward speed.

Battery Meter (See Figure 1, Item "J")

The battery meter indicates the amount of charge that is left in the batteries while the machine is in use. When the charge gets too low the brush/

pad motors will shut off.

Circuit Breakers (See Figure 1, Item "K & L")

The circuit breakers for the brush motors are located on the control panel. If a circuit breaker trips, determine which motor is not operating and turn

the key switch "OFF". Wait ﬁ ve minutes and push the reset button back in. Turn the key switch "ON", and try again. An authorized service person

should be contacted if the breaker trips again.

Hour Meter (Optional) (See Figure 1, Item "M")

The hour meter indicates the number of hours the machine has operated. It runs only when the machine is moving forward or reverse. The hour

meter is standard equipment for model 56383986.

Chemical Mixing Control (Optional) (See Figure 1, Item "N")

The chemical mixing control regulates the amount of concentration of cleaning chemical mixed with the clear water from the solution tank. Turning

the chemical mixing knob clockwise increases the concentration of chemical.

Battery Charge Status LED (See Figure 1, Item "O")

The battery charge status LED indicates status of charging. Flashing green indicates the batteries are currently charging. Steady on green light

indicates the batteries are fully charged.

Emergency Stop (Model 56383986 only) (See Figure 1, Item "P")