Publicidad
Idiomas disponibles
Idiomas disponibles
English
•
Always use trigger lock-off when tool is not in
immediate use. Using the trigger lock-off will prevent
accidental discharge.
•
Do not overreach. Maintain proper footing and balance
at all times. Loss of balance may cause personal injury.
Use the tool only for its intended use. Do not
•
discharge fasteners into open air, concrete, stone,
extremely hard woods, knots or any material too
hard for the fastener to penetrate. Do not use the
body of the tool or top cap as a hammer. Discharged
fasteners may follow unexpected path and
cause injury.
•
Always keep fingers clear of contact trip to prevent
injury from inadvertent release of the Pusher
•
Refer to the Maintenance and Repairs sections for
detailed information on the proper maintenance of
the tool.
Always operate the tool in a clean, lighted area.
•
Be sure the work surface is clear of any debris and be
careful not to lose footing when working in elevated
environments such as rooftops.
•
Do not drive fasteners near edge of material. The
workpiece may split causing the fastener to ricochet,
injuring you or a co-worker. Be aware that the staple
may follow the grain of the wood (shiner), causing it to
protrude unexpectedly from the side of the work material.
Drive the chisel point of the staple perpendicular to the
grain to reduce risk of injury.
•
Do not drive staples onto the heads of other
fasteners or with the tool at too steep an angle.
Personal injury from strong recoil, jammed fasteners, or
ricocheted staples may result.
•
Keep hands and body parts clear of immediate work
area. Hold workpiece with clamps when necessary to
keep hands and body out of potential harm. Be sure the
workpiece is properly secured before pressing the stapleer
against the material. The contact trip may cause the work
material to shift unexpectedly.
•
Do not use tool in the presence of flammable dust,
gases or fumes. The tool may produce a spark that could
ignite gases causing a fire. Driving a staple into another
staple may also cause a spark.
•
Keep face and body parts away from back of the tool
cap when working in restricted areas. Sudden recoil
can result in impact to the body, especially when stapling
into hard or dense material.
•
Grip tool firmly to maintain control while allowing
tool to recoil away from work surface as fastener is
driven. In Rapid sequential mode if contact trip is allowed
to recontact work surface before trigger is released an
unwanted fastener will be driven.
•
Choice of triggering method is important. Check the
manual for triggering options.
4
Sequential/Rapid Sequential Selector
Switch
Sequential Action
•
When using the tool in sequential mode mode, do
not actuate the tool unless the tool is placed firmly
against the workpiece.
Rapid Sequential Action
•
When using the tool in rapid sequential action,
be careful of unin tentional double fires resulting
from tool recoil. Unwanted fasteners may be driven if
the contact trip is allowed to accidentally re-contact the
work surface.
•
To Avoid Double Fires:
ʵ Do not engage the tool against the work surface with
a strong force.
ʵ Allow the tool to recoil fully after each actuation.
ʵ Use tool in sequential mode.
•
When "rapid sequential" actuating the finish stapler,
always keep tool in control. Inaccurate placement of
tool can result in misdirected discharge of a fastener.
•
Do not drive staples onto the heads of other
fasteners. Strong recoil, jammed fasteners, or ricocheted
staples may result.
Be aware of material thickness when using stapler. A
•
protruding staple may cause injury.
•
Depth adjustment: To reduce risk of serious injury
from accidental actuation when attempting to
adjust depth, ALWAYS;
ʵ Remove battery pack.
ʵ Engage trigger lock.
ʵ Avoid contact with trigger during adjustments
•
Do not drive staples blindly into walls, floors or
other work areas. Fasteners driven into live electrical
wires, plumbing, or other types of obstructions can result
in injury.
•
Stay alert, watch what you are doing and use
common sense when operating a power tool. Do not
use tool while tired or under the influence of drugs,
alcohol, or medication. A moment of inattention
while operating power tools may result in serious
personal injury.
Additional Safety Information
WARNING: ALWAYS use safety glasses. Everyday
eyeglasses are NOT safety glasses. Also use face or
dust mask if cutting operation is dusty. ALWAYS WEAR
CERTIFIED SAFETY EQUIPMENT:
•
ANSI Z87.1 eye protection (CAN/CSA Z94.3),
•
ANSI S12.6 (S3.19) hearing protection,
•
NIOSH/OSHA/MSHA respiratory protection.
WARNING: Some dust created by power sanding,
sawing, grinding, drilling, and other construction
activities contains chemicals known to the State
of California to cause cancer, birth defects or
other reproductive harm. Some examples of these
chemicals are:
Publicidad
