Publicidad
1.5.9. Avoid charging the battery at temperatures below 0 ° C.
1.5.10. The charger supplied with the cordless drill is designed to work with it only. It should not be used for other purposes.
1.5.11. Do not place any metal objects in the charger.
1.5.12. Do not change the direction of rotation of the spindle of the cordless drill during operation. This will damage her.
1.5.13. To clean the cordless drill, use soft and dry cloth. Never use any solvent or alcohol.
1.5.14. Before cleaning the charger, unplug the charger.
1.5.15. If you are going to charge batteries consecutively one after the other, make a 30-minute break between charges.
1.6. Special safety precautions when operating the charger.
Before charging the charger, all relevant information and information contained in this instruction manual as well as the
charger and battery charging instructions for this charger must be read.
1.6.1. To reduce the risk of personal injury and injuries, the charger must only be used to charge lithium-ion batteries. Other
types of batteries may explode, cause serious injuries or other material damage.
1.6.2. Do not expose the charger to the influence of moisture or water.
1.6.3. The use of connection, non-recommended or non-sold items by the charger manufacturer is liable to cause a fire,
cause bodily injury or electric shock.
1.6.4. The power cord should not be inserted. It should not be in a passage where people pass and should not be subjected
to any other danger (for example too much tension).
1.6.5. If there is no need, do not use an extension. Using an inappropriate extension may cause a fire or electric shock. If
using an extension cord is necessary, first make sure that the extension of the extension extends to the pins of the original power
supply plug.
1.6.6. The extension must be in the correct technical condition.
1.6.7. Do not use the charger with a damaged power cord or plug. The fault must be removed by a qualified person.
1.6.8. It is not allowed to use the charger if it has been subject to a strong shock, fall or has been damaged in any other way.
Verification and eventual repair must be entrusted to an authorized RAIDER service center.
1.6.9. Do not disassemble the charger. All repairs should be entrusted to an authorized RAIDER service center. Incorrect
installation of the charger will cause an electric shock or fire.
1.6.10. Before proceeding with any service or cleaning the charger, it must be disconnected from the mains.
1.6.11. Disconnect the charger from the mains when not in use!
2. Design and use.
The cordless drill is a power tool powered by a battery. It is driven by a DC electric motor with permanent magnets and a
planetary gear with cylindrical gears. The cordless drill is designed to screw and unscrew screws and bolts in wood, metal and
plastics as well as drill holes in the listed materials. Power tools with cordless, cordless power supply are especially suitable for
work related to interior decoration, room adaptation, and more.
It is not allowed to use the power tool for activities other than its intended purpose!
3. Noise and vibration data.
Sound pressure level: Lp
Sound power level: Lw
Vibration acceleration value: a
4. Preparing for work.
4.1. Inserting and removing the battery.
The direction of rotation switch is placed in the middle intermediate position. In this situation, the trigger is blocked.
Press the button (6) and the battery is removed.
Place the charged battery in place and clear the lock button
4.2. Charge the battery.
The cordless drill is supplied with a partially charged rechargeable battery. The battery must be fully charged before use.
Charging should be carried out at an ambient temperature in the range of 4 ° C to 40 ° C. A new battery or one that has not been
used for a long time acquires its full capacity after about 5 charging and discharging cycles.
The grid voltage must correspond to that indicated on the charger plate.
Before starting charging, always check the charger status and the power cord first.
To charge the battery, only the charger supplied with the battery drill should be used.
The charger must not be subjected to rain, moisture or liquid pouring.
4.2.1. The direction switch is set to the center position.
4.2.2. Remove the rechargeable battery from the battery.
4.2.3. Connect the battery to the charger.
4.2.4. Plug the charger into the mains (230 V).
= 77.8 dB(A) K=3 dB(A)
A
= 88.8 dB (A) K = 3 dB (A)
A
= 1.020 m/s
2
h
11
Publicidad
