Publicidad
Idiomas disponibles
Idiomas disponibles
mode should be used in the lowest speed that results
in an appropriate feed rate and chip clearing for
the material.
CAUTION: When using advanced tapping mode,
always start with the default forward time and reverse
time shown in Table 4, then increase or decrease
as necessary.
When the Precision Tap™ is enabled, the tool will operate in
forward and then automatically operate in reverse without
releasing the trigger. The tool will continue to alternate
between forward and reverse until the trigger is released.
D
WALT Tool Connect™
e
WARNING: To reduce the risk of injury, remove
accessories from the tool anvil before any Tool
Connect™ interaction.
NOTICE: Always check the tool configuration prior
to use. If you are unsure of the current configuration,
press the mode selector button
tool to the Home setting as described on the label and
this manual.
The DCF896 and DCF896H are capable of connecting
with mobile devices that support Bluetooth® Smart (or
Bluetooth® 4.0) technology. (To see if your mobile device
is compatible, visit: http://www.bluetooth.com/Pages/
Bluetooth-Smart-Devices-List.aspx)
D
WALT Tool Connect™ is an optional application for your
e
smart device (such as a smart phone or tablet) that connects
the device to your tool to allow you to configure specific
tool functions. Refer to Tool Connect™ Mode Selector.
NOTE: The Bluetooth® word mark and logos are registered
trademarks owned by the Bluetooth®, SIG, Inc. and any use
of such marks by D
WALT is under license. Other trademarks
e
and trade names are those of their respective owners.
nOTE: The Tool Connect™ App is governed by separate
terms and conditions available for viewing through the
mobile application.
Download the D
WALT Tool Connect™ application at:
e
•
Follow the instructions in the app to create your Tool
Connect™ account.
•
On the Home screen of the app, select "+ Tool" to begin
the process of adding your tool to the app.
•
To connect your tool with the D
app, at the appropriate screen, press the mode selector
button
for 3–5 seconds, then wait for the tool to
8
connect. The tool can only be connected to one Tool
Connect™ account at a time.
•
Once the tool has been connected, you can confirm that
you would like to register the product.
For more information on D
WALT Tool Connect™
e
functionality and features, please call 1–800–4-D
(1–800–433–9258), visit www.D
8
(Fig. D) to set the
WALT Tool Connect™
e
WALT
e
WALT.com or view
e
the FAQ page and help screens located inside the
mobile application.
Coin Cell Battery
Bluetooth® capability is powered by one coin cell battery in
your tool, that when necessary, should be replaced by your
local D
WALT service center. Do not attempt to replace the
e
coin cell battery yourself.
WARNING: Danger of explosion if battery is
incorrectly replaced.
WARNING: DO NOT INGEST BATTERY; CHEMICAL
BURN HAZARD. This product contains a coin/
button cell battery. If the coin/button cell battery is
swallowed, it can cause severe internal burns in just
2 hours and can lead to death.
•
Keep new and used batteries away from children.
If the battery compartment does not close
securely, stop using the product and keep it away
from children.
•
If you think batteries might have been swallowed
or placed inside any part of the body, seek
immediate medical attention.
•
If the coin cell battery contents come into contact
with the skin, immediately wash area with mild
soap and water. If coin cell battery liquid gets
into the eye, rinse water over the open eye for
15 minutes or until irritation ceases. If medical
attention is needed, the battery electrolyte is
composed of an organic solvent and lithium salts.
•
Do not incinerate or dispose of tool together with
household waste material! Tool that has reached
the end of its life must be collected separately
and returned to an environmentally compatible
recycling facility.
Anvils (Fig. E, F)
WARNING: Use only impact-rated accessories. Non-
impact accessories may break and cause a hazardous
condition. Inspect accessories prior to use to ensure
that it con tains no cracks.
CAUTION: Inspect anvils, detent pins and hog rings
prior to use. Missing or damaged items should be
replaced before use.
Place the switch in the locked off (center) position or
remove battery pack before changing accessories.
Anvil with Detent Pin (Fig. E)
DCF896
To install an accessory on the anvil, align the hole in the
side of the accessory with the detent pin
Press the accessory on until the detent pin engages in the
hole. Depression of detent pin may be necessary to aid
installation of accessory.
To remove an accessory, depress the detent pin through
the hole and pull the accessory off.
English
9
on the anvil
3
.
9
Publicidad
