Publicidad
Idiomas disponibles
Idiomas disponibles
ETF SL21-04-I06-T25
Technical Data
Product Data
Motor voltage
Motor power
Speed
Torque range
Weight
Declarations
Liability
Many events in the operating environment may affect the
tightening process and shall require a validation of results. In
compliance with applicable standards and/or regulations, we
hereby require you to check the installed torque and rotational
direction after any event that can influence the tightening re-
sult. Examples of such events include but are not limited to:
• initial installation of the tooling system
• change of part batch, bolt, screw batch, tool, software,
configuration or environment
• change of air- or electrical connections
• change in line ergonomics, process, quality procedures or
practices
• changing of operator
• any other change that influences the result of the tighten-
ing process
The check should:
• Ensure that the joint conditions have not changed due to
events of influence.
• Be done after initial installation, maintenance or repair of
the equipment.
• Occur at least once per shift or at another suitable fre-
quency.
EU DECLARATION OF INCORPORATION
We, Atlas Copco Industrial Technique AB, SE-105 23
STOCKHOLM SWEDEN, declare under our sole responsi-
bility that this product (with name, type and serial number,
see front page) fulfils the following essential requirements of
Machinery Directive 2006/42/EC:
2006/42/EC (MD), 2011/65/EU (RoHS), 2014/30/EU
(EMC), 2015/863/EU (RoHS amendment)
This partly completed machinery must not be put into service
until the final machinery into which it is to be incorporated
has been declared in conformity with provisions of the Ma-
chinery Directive 2006/42/EC, where appropriate.
The following (parts/clauses of) European harmonized stan-
dards have been applied:
EN 55014-1:2017 + A11:2020, EN 55014-2:2015, EN
61000-6-2:2005+AC:2005, EN 61000-6-2:2019, EN
61000-6-4:2007+A1:2011, EN 62841-1:2015+AC:2015, EN
62841-2-2:2014 +AC:2015
35 V 3 a.c.
140 W
1600 r/min
0.8 - 4 Nm ( - ft lb)
0.95 kg (2.1 lb)
© Atlas Copco Industrial Technique AB - 9836 2718 00
The relevant technical documentation was compiled and was
communicated in accordance with Machinery Directive
2006/42/EC part B of Annex VII. Authorities can request the
technical file in electronic form from:
Aleksandra Duric, Product Compliance Manager, Atlas
Copco Industrial Technique AB, SE-105 23 Stockholm Swe-
den
Stockholm, 6 March 2023
Carl von Schantz, Managing Director
Signature of issuer
Noise Declaration Statement
• Sound pressure level <70 dB(A) , uncertainty dB(A), in
accordance with ISO15744.
• Sound power level dB(A) , uncertainty dB(A), in accor-
dance with ISO15744.
These declared values were obtained by laboratory type test-
ing in accordance with the stated standards and are suitable
for comparison with the declared values of other tools tested
in accordance with the same standards. These declared values
are not adequate for use in risk assessments and values mea-
sured in individual work places may be higher. The actual ex-
posure values and risk of harm experienced by an individual
user are unique and depend upon the way the user works, the
workpiece and the workstation design, as well upon the expo-
sure time and the physical condition of the user.
We, Atlas Copco Industrial Technique AB, cannot be held
liable for the consequences of using the declared values, in-
stead of values reflecting the actual exposure, in an individual
risk assessment in a work place situation over which we have
no control.
We recommend a programme of health surveillance to detect
early symptoms which may relate to noise exposure, so that
management procedures can be modified to help prevent fu-
ture impairment.
The noise emission is given as a guide to the machine-
builder. Noise emission data for the complete machine
should be given in the instruction manual for the ma-
chine.
WEEE
Information concerning Waste of Electrical and Electronic
Equipment (WEEE):
This product and its information, meets the requirements of
the WEEE Directive (2012/19/EU), and must be handled in
compliance with the directive.
The product is marked with the following symbol:
Safety Information
3
Publicidad
