IPC Mistral-H PW-H101 Instrucciones De Montaje página 26

USING HOT WATER AND VAPOUR (If available)
For a correct use of the Hot Water and Vapour Mode (if availa-
ble), it's advisable to use the following temperatures:
- Light dirt: 30 - 50 °C:
- Proteic dirt, e.g., in the food sector: 60 °C Max
- Cleaning Automobile or Machine Tools: 60 - 90 °C
- Debinding, Persistent greasy dirt: 100 - 110°C
- Facade cleaning, Sanitization of surfaces: up to 140 °C
To use the Vapour mode, nozzel series A.P. must be sub-
stitute with the recommended vapour nozzle offered as
Optional accessory.
For adjustments, refer to the "Control Panel"
With working temperature more than 95°C (203°F), the pressure
that indicates on the manometer must be
(460 PSI).
!
Danger
During use with boiling water, "Steam Phase", keep away
from the openings for fumes discharge (risk of burning).
When you have finished using the "Hot Water or Steam
Phase", let the machine cool down for about 3 minutes
with the gun turned on.
ADVICE ON USING DETERGENTS
!
Warning
This appliance has been designed for use with the detergents
and/or chemicals supplied or recommended by the manufac-
turer. The use of other detergents or chemicals may influence
the safety of the cleaner.
1)
For environmental compatibility, we recommend a reasona-
ble use of detergents, according to the instructions on the pack.
2) From the range of recommended products, choose the
one most suited to the washing job to be done and dilute it
with water according to the instructions on the pack or in the
catalogue of the detergents most suited for the type of hot or
cold water cleaner.
3) Ask your dealer for the detergents catalogue.
OPERATING PHASES FOR CORRECT CLEANING WITH
DETERGENTS.
1) Prepare the solution of detergent at the concentration most
suitable for the type of dirt and the surface that is to be washed.
2) Start the cleaner, turn on the detergent tap, and spray the
dirty surface with the diluted product, working from bottom to top.
Let it react for a few minutes.
Refer to the "Control Panel".
English
3) Rinse the whole surface well from top to bottom with hot or
cold water at high pressure.
4) Disinfect the surface by spraying it with hot water > 90°C,
which is achieved by positioning the temperature selector on
the Hot Water. Refer
!
Using very hot water may affect the efficiency of rubber parts
(tyres, gaskets, etc.).
5)
by operating the pump for one minute with the detergent tap
completely closed.
STOPPING THE CLEANER
1) Switch off the burner by turning the pressure regulator to
pos. "0" (fig. 8B).
2) Let the cleaner run with cold water only for at least 30 seconds
to cool down the boiler.
< a 32 bar
3) Stop the cleaner by turning the selector switch to pos. "0"
(fig. 8A).
4) Discharge the pressure from the H.P. hose by pressing the
trigger on the gun.
5)
supply via the omnipolar switch or by unplugging the plug from
the socket.
6) Turn off the water supply tap (fig. 6A).
!
- If the water cleaner is left, even temporarily, turn it off by using
the omnipolar switch or by unplugging the plug from the socket.
- Water cleaners with the "Total Stop" device should be consid-
ered as off when the omnipolar switch is in the "O" position or
the plug is unplugged from the
socket.
- When the water cleaner is not
used, close the safety device
on the handle. (fig. 12)
- Dry use of the water cleaner
causes serious damage to
pump gaskets.
- 26 -
to the "Control
Warning
After use with detergent, rinse the high pressure water circuit
Disconnect the water cleaner from the mains electricity
Warning
Panel".
FIG. 12