Settings - AEG AR 4025 BT Manual De Instrucciones

ENGLISH
76

Settings

Adjust the volume
WARNING:
Setting the volume too high may damage your
hearing!
If the volume is set too high your hearing may be
permanently damaged.
►
Set the volume to a reasonable level.
Turn the multijog (3) to set the volume.
‹
Switch unit to mute
PWR/MUTE button (2) to switch the unit to
Press the
‹
mute.
Press the PWR/MUTE button (2) again to deactivate
‹
the function.
Sound settings
Press the multijog (3). The current volume is displayed.
‹
Press the multijog each time to select the next option.
The following settings are available:
VOL - Volume (from 0 to 100),
BAS - Bass (from -10 to +10)
TRB - Treble (from -10 to +10)
BAL - Balance (Sound balance between the right and
left speaker) (from 10L to 10R)
FAD - Fader (Sound balance between the rear and
front speaker) (from 10F to 10R)
DSP - Equalizer (Digital Sound Processing) (FLAT, CLAS-
SICS, POP M, ROCK M, DSP OFF)
Turn the multijog to adjust the displayed setting.
‹
More settings via the multijog
Keep the multijog (3) pressed for a few seconds to
‹
access more settings options. Press the multijog each
time to select the next option.
Turn the multijog to adjust the displayed setting.
‹
The following settings are available:
TA
Traffic announcement settings
■
TA SEEK : If the TA function is activated,
the unit will try to select a station which is
broadcasting traffic information.
■
TA ALARM:
The station is not automati-
cally preset. If no traffic information is
received a buzzer sounds and NO TP/TA is
shown on the display If the selected
station is not transmitting a RDS-Signal,
SEEK PI is shown n the display.
PI
If you are driving through an area in which
two stations with the same AF- but different
PI-Code (PI = Programme information) – can
be received, the reception will then become
instable. In this situation you have a choice
between:
■
PI SOUND: If the unit switches over in any
case to the other station, the sound from
the other station will only be heard for less
than one second.
■
PI MUTE: The sound of the other station is
suppressed.
RETUNE Time frame for automatic tuning into traffic
information or program information:
■
S (Short) after around. 30 seconds
■
L
(Long) after around 90 seconds
MASK This option decides which stations should be
excluded from the station scan:
■
DPI: Alternative frequencies with different
PI-Code are excluded from the scan.
■
ALL: Alternative frequencies with differ-
ent PI-Code and without RDS-Information
with high signal levels are excluded.
TA VOL
Traffic information volume
EON TA The unit can receive RDS EON data. EON
means the transmission of additional station
information within a station group. In the
event of a traffic announcement (TA) it will
switch within a station group from a non-
traffic broadcast to the corresponding traffic
radio station of the station group.
■
DX: the unit attempts to receive the EON
TA information from a station within range
and thus to improve the reception quality.
■
LO:
Prevents switching over to a station
with too weak a signal level.
BEEP
Sound heard when a button is pressed:
■
BEEP 2ND:
Unit beeps when a button with
multiple functions is kept pressed.
■
BEEP ALL: A beep sounds whenever a
button is pressed
■
BEEP OFF:
no beep
Stereo/
Switch between Stereo and Mono
Mono
Loudness The bass is amplified when the Loudness
function is activated.
■
LOUD ON: Loudness function is
activated.
■
LOUD OFF: Loudness function is
deactivated.
DX/LOCAL Switches between local and more distant
stations.
■
DX:
Receive other more distant stations.
■
LOCAL: Receive local stations.
Show Display information
Press the DIS (40) button several times to display the
‹
following information on the display in sequence: