Descargar Imprimir esta página

IPC ML CMP D1310P M Manual De Instrucciones página 24

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 55
DESIGNATED USE
The appliance is designed exclusively for the cleaning of ma-
chinery, vehicles, buildings, utensils and in general surfaces
suitable for treatment with a high pressure jet of cleaning solu-
tion at between 25 and 250 bars (360-3600 PSI).
It has been designed for use with the detergents supplied or
recommended by the Manufacturer.
The use of other detergents or chemicals products may jeopar-
dise the safety of the appliance.
This appliance must be used exclusively for the purposes for
which it was designed.
All other uses are considered improper and unreasonable.
Examples of unreasonable use include:
- Washing surfaces not suitable for treatment with a high
pressure jet.
- Washing people, animals, electrical appliances and the
appliance itself.
- Use of unsuitable detergents or chemical products.
- Blocking the lance trigger in the delivery position.
Improper, incorrect or unreasonable use absolves the Manu-
facturer of all liability.
All high pressure washers are constructed in compliance with
current safety standards and regulations.
PRELIMINARY OPERATIONS
UNPACKING
After unpacking the high pressure washer, make sure it is intact
and undamaged.
If in doubt, do not use.
Contact your dealer.
Packaging elements (plastic bags, boxes, nails, etc.) must not
be left within reach of children as they are a potential source of
danger and must be disposed of or stored in compliance with
national environmental protection standards.
ASSEMBLING DISASSEMBLED PARTS OF THE MACHI-
NE.
The main parts of the machine and safety devices are assem-
bled by the Manufacturer.
To facilitate packing and transport, a number of secondary
components of the high pressure washer are supplied disas-
sembled.
The user is responsible for assembling these components ac-
cording to the instructions provided in each assembly kit.
RATING PLATE:
The rating plate with the principal technical characteristics
of your high pressure washer is located on the trolley and is
always visible.
English
Warning
!
On receipt of the product, make sure the rating plate is
present. Otherwise contact the Manufacturer and/or dealer
immediately.
Use of equipment without a rating plate absolves the Manu-
facturer of all liability. Products without a rating plate must
be considered anonymous and potentially dangerous.
MULTIPLE INSTALLATION
The wall mounted high pres-
sure washer can be stacked
in columns of a maximum of
three modules.
Fit the feet into the correspon-
ding housings on the frame.
The wall mounted high pres-
sure washer must always be
fixed to a wall by means of
screws.
COMMAND AND CONTROL DEVICES
!
Warning
Before connecting the high pressure washer to the mains
electricity and water supplies, you should familiarise yourself
with the command and control devices.
To do this, follow the instructions in this manual and refer to
the relative figures.
CONNECTIN G TO TH E
MAINS WATER SUPPLY
Connect the water supply
hose to the mains water sup-
ply (fig. 2A) and to the coupling
on the high pressure washer
(fig. 2B). Check that the mains
water supply provides a suf-
ficient quantity and pressure
of water to operate the high
pressure washer 2 - 8 BAR.
(29 - 116 PSI).
Maximum inflow water tempe-
rature 50°C. (122°F).
ASSEMBLING THE ACCES-
SORIES
!
Warning
Risk of injury.
Use only original accessories
provided or authorised by the
Manufacturer.
Mount the accessories only
when the appliance is off.
Connect the high pressure
hose to the high pressure
washer (fig. 2C) and to the
lance (fig. 3).
- 20 -
FIG. 1
A
C
B
FIG. 2
FIG. 3

Publicidad

loading