Publicidad
Idiomas disponibles
Idiomas disponibles
English
Using an Accessory Tool (Fig. I)
Your vacuum may come with some of the following tools.
‑
Crevice tool.
‑
2 in 1 brush
‑
Pet head (BHFEA640WP only)
‑
Powered pet head (BHFEA640WP only).
•
The accessories
16
,
17
directly to the extension tube
as shown in Fig. I.
•
Align the top of the accessories
the vacuum inlet
7
or extension tube
into place until the accessory release latch
position as shown in Fig. I.
Extension Tube Accessory Storage (Fig. J)
Accessories
16
,
17
,
19
tube
8
using the on clip on accessory holder
1. Align the clip on accessory holder
the extension tube
8
2. Push firmly so that the clip on accessory holder
held firmly on position on the extension tube
3. Align the top of the accessories
clip on accessory holder
into position.
Wall Mounted Accessory Storage (Fig. J)
1. The accessories
16
,
17
directly to the wall mounted accessory storage and
charging station
22
.
2. Align the top of the accessories
the wall mounted accessory storage arms and charging
station
and slide it on until it locks into position.
22
nOTE: The accessory storage side arms
removed from the charging station
for the user to do if they don't have enough space or only
want to utilize one side arm
‑
To remove the accessory storage side arms
the charging station
upwards and away from the charging station
To reconnect, align the side arms
‑
locking holes on the charging station
downward until they lock into position.
MAINTENANCE
WARNING:
serious personal injury, turn unit off before
making any adjustments or removing/installing
attachments or accessories. An accidental start‑up
can cause injury.
Cleaning
WARNING:
all air vents with clean, dry air at least once a week.
To minimize the risk of eye injury, always wear ANSI
10
,
19
,
20
can be fitted either
8
or to the vacuum inlet
16
,
17
,
19
,
20
8
and push
9
locks into
can be stored on the extension
18
.
18
onto the back of
.
8
16
,
17
,
19
with the
18
and slide it on until it locks
,
19
,
20
can be fitted
,
,
,
16
17
19
20
38
can be
22
. This is possible
38
.
22
, pull the side arms
with the
38
22
and press
To reduce the risk of
Blow dirt and dust out of
Z87.1 approved eye protection when performing
this procedure.
WARNING:
harsh chemicals for cleaning the non‑metallic parts
of the tool. These chemicals may weaken the plastic
materials used in these parts. Use a cloth dampened
only with water and mild soap. Never let any liquid get
7
inside the tool; never immerse any part of the tool into
a liquid.
with
Cleaning and Emptying the Vacuum
WARNING:
never use the vac without its filter.
iMPORTAnT: Maximum dust collection will only be
obtained with clean filters and an empty dust canister.
If dust begins to fall back out of the product after it is
switched off, this indicates that the dust canister is full and
requires emptying.
18
is
nOTE: There is a MAX line on the dust cannister. Do not allow
.
the dust cannister to fill beyond this point.
nOTE: The filters are re-usable do not throw it away when the
product is emptied.
nOTE: We recommend that you replace the filters
every 6–9 months depending on frequency of use.
To Empty the Dust Canister (Fig. K, N)
1. Press the dust canister release button
lift away dust canister
with
in Fig. K.
2. Lift and remove the lift away dust canister
unit
28
3. While over top of a trash can, press the dust canister
door release button
canister
4. Empty the contents of the lift away dust canister
38
from
5. Tap the lift away dust canister
38
firmly
excessive dust and debris.
22
.
Removing and Installing the Pre-filter
(Fig. K, L)
nOTE: The pre-filter fits snuggly in the dust canister and may
be difficult to remove at first.
1. Lift and remove the lift away dust canister
unit
28
2. While over top of a trash can, grip the recessed tabs
the pre-filter
with cyclones and filter housing
3. Shake off or lightly brush any loose dust.
4. Install the pre-filter
ensuring the dust canister slot
recessed tabs
5. Install the dust canister
clicks firmly into position.
Never use solvents or other
Projectile/Respiratory Hazard:
12
from the unit
as shown in Fig. K.
11
to empty the lift away dust
12
as shown in Fig. N.
12
as shown in Fig. K.
29
and pull upwards to remove the pre-filter
10
29
into the dust canister
32
25
as shown in Fig. L.
12
onto the unit
31
,
6
13
to release the
28
as shown
12
from the
12
.
as necessary to remove
12
from the
25
of
.
12
aligns with the
28
, until it
Publicidad
