MECH MIND NANO Manual De Usuario página 2

1. Safety Information
To ensure safe use, please do not use the product before reading this manual
●
and becoming familiar with the correct usage. Improper use and maintenance
may damage the product or cause other hazards. Mech-Mind shall not be
liable for any injury or damage brought upon the user or any third party due to
improper use and maintenance.
Following the instructions and warnings in this manual can lower risks, but can
●
not totally eliminate all risks.
Every step has been inspected during the drafting of this user manual. Please
●
do not hesitate to contact Mech-Mind if you find any problems or mistakes in
the manual.
This product is to be mounted, connected, used and maintained by trained
●
adults only. To ensure safe operation, the product should be transported,
stored, mounted, connected, used and maintaind properly.
Laser is hazardous. Please familiarize yourself with hazard prevention before
●
using the camera.
Precautions for Mounting and Using the Camera
It is PROHIBITED to place any explosive or flammable substances near the
●
camera. Do not expose the camera to open fire or high temperature.
Do not throw, drop, or collide the camera with other objects. The camera may
●
be damaged by strong shock or vibration. It is PROHIBITED to modify the
camera in any form. Do not repair or disassemble the camera by yourself.
Mech-Mind shall not be liable for any damage caused by repair or disassembly
not performed by Mech-Mind.
Do not allow any foreign object, such as metal pieces, dust, paper, wood chips,
●
etc., to enter the camera. Failure to do so may lead to fire, electric shock,
malfunction, etc.
Do not use the camera at extremely high or low temperature. The operating
●
temperature range is -10–45°C for the LSR and DEEP series, and 0–45°C for
other series of Mech-Eye Industrial 3D Camera.
Please use the camera indoors.
●
Please use the camera at elevations below 4,000 meters.
●
Do not stare into the light beam when using the camera.
●
Please install the camera in a well-circulated, open place.
●
Check the Camera
Before using, please check the camera carefully for damage, signs of water entry,
●
suspicious odor, smoke, loose or damaged bolts, etc., and make sure that the
camera is in proper working conditions. If any of the above abnormalities occur,
please disconnect the power immediately.
High temperature will age the power cable. Please check the power cable
●
regularly for signs of aging. If the cable has aged, please contact Mech-Mind to
acquire a replacement.
01
Usage of Adapter / DIN Rail Power Supply
DO NOT use if the power port, adapter/DIN rail power supply, or power socket is
●
wet.
DO NOT heat or put the adapter/DIN rail power supply and power cable in fire.
●
For power, please use a 24 V isolated adapter with an output power of 36 W
●
(for the NANO series) or 90 W (for the other series) or a 24 V isolated DIN rail
power supply.
Please use the specified voltage. Failure to do so may lead to fire, electric
●
shock, malfunction, etc. The adapter/DIN rail power supply and power cable
should be properly grounded. It is recommended to use the isolated adapter/
DIN rail power supply provided by Mech-Mind.
Use copper conductors only.
●
Power plugs should be properly grounded. Do not place the adapter/DIN rail
●
power supply in a place that is hard to disconnect the power.
Precautions for Using Laser Cameras
DO NOT look into the laser beam or the reflected laser beam directly. Do not
●
look into the laser beam with optical instruments. Failure to do so may lead to
eye injuries.
DO NOT direct the laser at other people. The laser beam must be lower or
●
higher than and never at eye level.
Be cautious of the path of the laser beam. If there is a possibility that personnel
●
may be exposed to the specular or diffuse reflections, block the beam by
installing a protective enclosure.
Do not enter the areas that the laser/reflected laser output reaches. Do not
●
place any reflective light object (mirror, glass, metal, etc.) in the path of the
laser beam.
LASER ENERGY - EXPOSURE NEAR APERTURE MAY CAUSE BURNS.
●
NOTE: The risk of skin injury is only likely for highly divergent beams for
●
exposure close to the aperture.
Notice for Disposal
Please comply with local laws and regulations when disposing of the camera
●
to avoid polluting the environment. Please do not dispose of the camera
irresponsibly. Improper disposal may pollute the environment.
The pollution degree of the camera is 3.
●
EN EN
02