EINHELL GC-KS 18 Li Manual De Instrucciones Originales página 23

3. Proper use
The chainsaw is intended for felling trees and for
cutting trunks, branches, wooden beams, boards
etc. and can be used for cross cuts and longitudi-
nal cuts. It is not suitable for cutting any materials
other than wood.
The equipment is to be used only for its prescri-
bed purpose. Any other use is deemed to be a
case of misuse. The user / operator and not the
manufacturer will be liable for any damage or inju-
ries of any kind caused as a result of this.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.
4. Technical data
Motor power supply: ............................... 18 V DC
Idle speed n₀: .....................................2,400 min
Cutter rail length ..................................... 250 mm
Max. cutting length: ................................ 230 mm
Cutting speed at rated rpm: ......................4.5 m/s
Saw chain: ......................................... 91PJ040X
Oil tank capacity: .......................................200 ml
Cutter rail: .......................................100SDEA041
Weight: ......................................... approx. 2.6 kg
Caution!
The equipment is supplied without batteries and
without a charger and is allowed to be used only
with the lithium-ion batteries of the Power-X-
Change series!
The lithium-ion batteries of the Power-X-Change
series are allowed to be charged only with the
Power-X charger.
Danger!
Sound and vibration
Sound and vibration values were measured in ac-
cordance with EN 62841-1 and EN 62841-4-1.
L sound pressure level ..................... 86,8 dB(A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level ........................ 96,6 dB(A)
WA
K uncertainty ........................................ 2,75 dB
WA
L sound power level guaranteed ......... 99 dB(A)
WA
Anl_GC_KS_18_Li_SPK7.indb 23 Anl_GC_KS_18_Li_SPK7.indb 23
GB
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) were determined in accordance with
EN 62841-1 and EN 62841-4-1.
Handle under load
Vibration emission value front handle
a = 3.87 m/s
2
h
Vibration emission value rear handle
a = 3.69 m/s
2
h
K uncertainty = 1.5 m/s
The stated vibration emission levels and stated
noise emission values were measured in ac-
cordance with a set of standardized criteria and
can be used to compare one power tool with
another.
The stated vibration emission levels and stated
noise emission values can also be used to make
an initial assessment of exposure.
-1
Warning:
The vibration and noise emission levels may vary
from the level specifi ed during actual use, depen-
ding on the way in which the power tool is used,
especially the type of workpiece it is used for.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
5. Before starting the equipment
Warning!
Always remove the battery pack before making
adjustments to the equipment.
Danger! Do not fi t the battery until the chainsaw
has been fully assembled and the chain tension
has been set. Always wear protective gloves
when working on the chainsaw to protect yourself
against injury.
- 23 -
2
18.07.2023 11:01:46 18.07.2023 11:01:46