Publicidad
Idiomas disponibles
Idiomas disponibles
SAFE OPERATION PRACTICES, cont'd
6. Regularly check the safety interlock system for
proper function, as described later in this manual.
If the safety interlock system does not function
properly, have your mower serviced professionally
by an authorized service dealer.
7. Never tamper with the blade control safety interlock
or other safety devices. Check for proper operation
per the Service and Maintenance section.
8. Check the mower blade and engine mounting
bolt torque in accordance to the Service and
Maintenance section in this manual. Also, visually
inspect blade for damage (e.g., excessive wear,
bent, cracked). Replace the blade with the original
equipment manufacturer's (O.E.M.) blade only.
9. Use of service parts which do not meet the original
equipment specifications may lead to improper
performance and compromise safety.
10. Keep all nuts, bolts, and screws tight to be sure the
equipment is in safe working condition. Check
all hardware for tightness per the Service and
Maintenance section.
11. After striking a foreign object, stop the engine,
disconnect the spark plug wire(s) and ground
against the engine. Thoroughly inspect the mower
for any damage. Repair the damage before starting
and operating
12. Never attempt to make wheel cutting height
adjustments or repairs to the mower while the
engine is running.
13. Grass catcher components and the discharge
cover are subject to wear and damage which
could expose moving parts or allow objects to be
thrown. For safety protection, frequently check
components and replace immediately with original
equipment manufacturer's (O.E.M.) parts only. "Use
of parts which do not meet the original equipment
specifications may lead to improper performance
and compromise safety. "
14. Maintain or replace safety and instruction labels,
as necessary.
15. Observe proper disposal laws and regulations for
gas, oil, etc. to protect the environment.
Notice Regarding Emissions
Engines which are certified to comply with
California and federal EPA emission regulations
for SORE (Small Off Road Equipment) are certified
to operate on regular unleaded gasoline, and may
include the following emission control systems:
Engine Modification (EM) and Three Way Catalyst
(TWC) if so equipped.
When required, models are equipped with
low permeation fuel lines and fuel tanks for
evaporative emission control. California models
may also include a carbon canister. Please contact
Customer Support for information regarding the
evaporative emission control configuration for
your model.
Spark Arrestor
WARNING: This mower is equipped with an
internal combustion engine and should not
be used on or near any unimproved forest-
covered, brush-covered or grass-covered land
unless the engine's exhaust system is
equipped with a spark arrestor meeting
applicable local or state laws (if any).
If a spark arrestor is used, it should be maintained
in effective working order by the operator. In the
State of California the above is required by law
(Section 4442 of the California Public Resources
Code). Other states may have similar laws. Federal
laws apply on federal lands.
A spark arrestor for the muffler is available through
your nearest engine authorized service dealer or
contact the service department, P.O. Box 361131
Cleveland, Ohio 44136-0019.
Slope Gauge (Back Cover)
WARNING: Slopes are a major factor related
to slip and fall accidents which can result in
severe injury or death. All slopes require
extra caution. If you feel uneasy on the slope,
do not mow it. Do not mow on slopes greater
than 15 degrees (25%). Only mow across
slopes, never mow up and down slopes.
USE THE SLOPE GAUGE ON THE BACK COVER AS
SHOWN TO DETERMINE IF A SLOPE IS TOO STEEP
FOR SAFE OPERATION!
To check the slope, proceed as follows:
1. Open manual to page and fold along the
dashed line.
2. Locate a vertical object on or behind the slope (e.g.
a pole, building, fence, tree, etc.)
3. Align either side of the slope gauge with the object.
4. Adjust gauge up or down until the left corner
touches the slope.
5. If there is a gap below the gauge, the slope is too
steep for safe operation.
7
Publicidad
