WaterLink SpinTouchFF Manual De Instruccion página 9

Brightness The brightness level of the display can be adjusted from 00 to 10. Tap
adjust the brightness. Tap
Date/Time The Year, Month, Day, Format, Hour, Minute, AM/PM can be set. Tap
adjust the displayed value. Tap
(minutes for 24 hour format, AM/PM for 12 hour format) tap
to exit to the Settings menu at any time.
Tap
Set Language There are ten language options – English, French, Spanish, German, Dutch,
Swedish, Portuguese, Italian, Turkish, Chinese. Tap selection. Tap
Calibration Tap to run an angle calibration to evaluate the alignment of the hub and disk. Tap
to exit to the Settings menu.
Power Options There are three power options: Auto Dim Time, Auto Off Time, and Power. Tap the
options then tap a selection. Tap selection. Tap
Bluetooth There are two Bluetooth options: Bluetooth Enabled and Fast Printer Connect that are
used to print test results. Tap
Other Settings About... lists the Serial Number, Firmware Version, Bluetooth MAC address,
Bluetooth Version and Test Count. The Test Count shows the number of complete tests that have
been performed over the lifetime of the meter. Tap
Ranges Enabled allows the option of having test results that are out of the range of the reagent
system displayed in red. The default setting is on.
RANGES
Freshwater (Code 4351)
Display
Test Factor Abbreviation
Alkalinity ALK
Ammonia AMMO
Hardness G HARD
Nitrate NITRATE
Nitrite NITRITE
pH pH
Phosphate PHOS
Saltwater (Code 4352)
Display
Test Factor Abbreviation
Alkalinity ALK
Ammonia AMMO
Calcium Ca
Magnesium Mg
Nitrate NITRATE
Nitrite NITRITE
pH pH
Phosphate PHOS
Test results that are out of range of the reagent system wil be RED.
accurate. Go SETTINGS>Other Settings to turn the Ranges Enabled feature OFF.
Testing samples for Nitrate immediately after treatment with a chlorine neutralizer containing
sodium thiosulfate will give low results. Retest in 2-3 days.
If the concentration of Calcium or Magnesium is out of the range listed above, the accuracy of
the results for Ammonia and Alkalinity will be affected. Nitrite levels greater than the range above
will affect the Nitrate results. Calcium and Ammonia results will be affected if salinity is not within
17 – 45 ppt.
to exit to the Settings menu.
to move to the next value. After the last value has been chosen
to exit to the Settings menu.
Range
0 – 250 ppm
0.0 – 3.0 ppm
0 – 500 ppm
0 – 300 ppm
0.0 – 2.0 ppm
4.5 – 10.0
0.0 - 2.0 ppm
Range
0 – 300 ppm
0.0 – 3.0 ppm
200 - 800 ppm
500 – 2200 ppm
0 – 60 ppm
0.0 – 2.0 ppm
6.5 – 10.0
0.0 – 2.0 ppm
9
to return to the Settings menu.
to exit to the Settings menu.
to exit to the Settings menu.
to return to the Settings menu.
Accuracy
± 15%
< 2.0 ppm: ± 0.2 ppm,
> 2.0 ppm: ± 0.4 ppm
± 15%
± 30%
± 0.2 ppm
± 0.2
± 0.2 ppm
Accuracy
± 15%
< 1.0 ppm: ± 0.2 ppm,
> 1.0 ppm: ± 0.4 ppm
±15 %
± 15 %
± 25%
± 0.2 ppm
± 0.2
± 0.2 ppm
RED
and
or to
Method
Detection Limit
15 ppm
0.2 ppm
20 ppm
5 ppm
0.1 ppm
NA
0.2 ppm
Method
Detection Limit
15 ppm
0.2 ppm
NA
NA
5 ppm
0.1 ppm
NA
0.2 ppm
test results may not be
to