Tabla de contenido
Publicidad
3. Using a 1/2"socket w rench, r emove twoself-
tapping screws, lockwasher a ndhexnutthathold
thedeckbeltcovertothedeck.SeeFigure 17. For
this,youwillhavetoworkfromthetopleftsideof
theridingmower. R emove t hebeltcover.
4. Using a 9/16" wrench, loosen thehexnutonthe
idlerpulley. S eeFigure 17.
5. Remove b eltfromaround deckpulley, i dlerpulley,
andtheengine pulley.
6. Place thenewbeltaround thedeckpulley andthe
engine pulleymaking surethatthebeltis routed
inside thebeltkeepers. Therearetwobeltkeepers
under t hegrass catcher, o neontheidler andthe
otherunder t hedeckbeltcover. S eeFigure 17.
7. Reinstall deckbeltcoverandsecure withtwoeach
ofself-tapping screw, l ockwasher a ndhexnut.
NOTE:
B elt keeper "A" must be mounted on the outside
of the belt.
8.
Make sure to align the belt keeper in line with the
frame. See Figure 17.
NOTE: An imaginary line between the belt keeper and
idler pulley should be parallel to frame. See Figure 17.
9.
Replace the grass catcher and pivot the hood
assembly back.
Lower Drive Belt
1.
Remove the rear deck belt guard following first five
steps for deck belt removal. Remove belt from the
engine pulley. See Figure 18.
Variable Speed Pulley
Spring
Spring
Loaded
Loaded
Idler
Pulley
2.
.
Figure 18
Push the spring loaded idler, located on the left side
of the transmission, to the right. Remove belt from
around the idler and then the transmission pulley.
See Figure 18.
Using a 9/16" socket, remove bolt, spacer and the
flat washer from the variable speed pulley.
4.
Drop the pulley down and remove the belt.
5.
Replace new belt and reassemble.
IMPORTANT: Make sure that the belt is routed inside of
belt keeper, and the belt keeper is reassembled in the
same location from where it was removed.
Upper
Drive
Belt
1.
Remove the engine pulley using a 5/8" socket
wrench with a 6" extension. The engine pulley is
located in front of the transmission.See
Figure 18.
2.
Drop the engine pulley down and remove the belt
from around it.
3.
Push the idler bracket to the right and remove the
belt. See Figure 18.
4.
Replace belt and reassemble.
Battery Service
The battery is located under the hood assembly. The
positive battery terminal is marked (+); the negative
battery terminal is marked (-).
Safe Handling
•
Shield eyes and protect skin and clothing when
handling battery acid (electrolyte) or a battery
containing acid.
•
Keep sparks, flame, cigarettes and other sources of
ignition away. Remember that battery contains
explosive gases.
•
Work in a well-ventilated area when filling
(activating), charging and using the battery.
_
WARNING:
Do not short battery terminals
by making a connection between either two
battery posts or between the positive terminal,
marked + on the battery, and the riding mower
frame. Before installing battery, remove metal
bracelets, wristwatch bands, rings etc. from
your person.
•
Always keep the rubber boot positioned over the
positive terminal to prevent shorting.
•
Connect positive terminal first to prevent sparks
from accidental grounding.
•
Do not use the riding mower battery to start other
vehicles.
,l_
WARNING:
Battery posts, terminals and
related accessories contain lead and lead
compounds. Wash hands after handling.
•
Always keep battery cables and terminals clean
and free of corrosive build-up.
•
After cleaning, apply a light coat of petroleum jelly
or grease to both terminals.
•
If removing the battery for any reason, disconnect
the NEGATIVE (black) wire from its terminal first,
followed by the POSITIVE (red) wire.
2O
Publicidad
Tabla de contenido
