Makita PDC1500 Manual De Instrucciones página 17

Choose a number on the base plate according to your
height by referring the table below.
Number on base plate
7
6
5
4
3
2
1
3.
Slide the base plate to the desired position while
pressing in the lever, and then release the lever to fix
the base plate.
► Fig.9: 1. Lever
4. Attach the battery to the shoulder harness assem-
bly as shown in the figure.
► Fig.10: 1. Battery
CAUTION:
Be careful not to pinch your
fingers or thumbs between the battery and the
shoulder harness assembly when attaching the
battery.
CAUTION:
Make sure that the battery is
securely fixed to the shoulder harness assembly.
Otherwise, the battery may fall when you put on the
unit or use the unit, and cause an injury. If you can
see the red indicator as shown in the figure, the bat-
tery is not locked completely.
► Fig.11: 1. Red indicator
CAUTION:
When removing the battery, press
the lock button while holding the handle firmly.
► Fig.12: 1. Handle 2. Lock button
Attach the adapter pocket to the waist belt with the hook
and loop fastener as shown in the figure.
► Fig.13: 1. Adapter pocket
NOTE: The adapter pocket can be attached on either
left or right side of the waist belt.
OPERATION
CAUTION:
When wearing the unit, be sure
to put shoulder harness on your both shoulders.
Otherwise, the unit may fall when you wear the unit or
use the unit, and cause an injury.
CAUTION:
When wearing the unit, be sure to
wear the unit on your back. Otherwise, the unit may
fall during operation and cause an injury.
CAUTION:
Always switch off the tool or
machine before turning on the unit, or connecting
the plug of the adapter or power tool/machine
to the socket of the battery. Otherwise, the tool or
machine may start suddenly and cause an injury.
Height
185 cm or more
180 - 190 cm
175 - 185 cm
170 - 180 cm
165 - 175 cm
160 - 170 cm
Up to 165 cm
17 ENGLISH
NOTE: The adapter for 18 V is not available for this
unit.
Using the cord holders
Attach the cord of the battery using the cord holders of
the shoulder harness assembly.
► Fig.14: 1. Cord holder
You can attach the cord of the battery to the cord hold-
ers as shown in the figure.
► Fig.15: 1. Cord holder
You can also attach the cord of the battery using only
the cord holder of the waist belt as shown in the figure.
► Fig.16: 1. Cord holder
You can also attach the cord of the battery to the cord
holders as shown in the figure.
► Fig.17: 1. Cord holder
CAUTION:
Be sure to attach the cord to the
shoulder harness on the left side only or right
side only so that the cord does not cross the
shoulder harness.
► Fig.18
CAUTION:
Attach only the cord of the battery
to the cord holders. Do not attach the cord of the
adapters or power tool/machine to the cord hold-
ers. Attaching the cord of the adapters or power tool/
machine may invite accident and cause an injury.
► Fig.19
► Fig.20
Connecting the unit to the tool or
machine
1. Remove the battery from the shoulder harness
assembly.
2.
Pull out the cord from either left or right side of the
battery. When pulling out the cord, be sure to set the
cord in the holders as shown in the figure.
► Fig.21: 1. Cord 2. Holder
You can also pull out the cord downward as shown in
the figure.
► Fig.22
3.
Attach the battery to the shoulder harness
assembly.
4. Insert the plug of the adapter or power tool/
machine into the socket of the battery all the way so that
the arrow mark on the plug is aligned with that on the
socket.
► Fig.23: 1. Plug 2. Socket 3. Arrow mark
NOTICE:
When disconnecting the plug and
socket, do not hold the cords but hold the plug
and socket. Otherwise, the cords may be damaged
and cause a malfunction of the unit.
NOTE: The plug and socket are disconnected if a
certain load is applied.