GE 20" Wide Manual De Instrucciones página 3

r_ 3-WIRE INSTALLATION (GROUND ISTHROUGH THE NEUTRALWIRE)
AWARNING:
Shock Hazard
The neutral wire and ground strap must be
connected as shown below for the range to be
properly grounded. Do not remove the ground strap.
Failure follow this instruction may result in potential
shock hazard.
Terminal block
(appearance
may vary)
AWARNING:
Fire hazard Neutral
Terminal block screws must be securely tightened, terminal
Failure to do so may result in potential fire hazard.
FOR POWER CORD INSTALLATION strap
A. Remove the 3 lower screws from the terminal Ground
block. Do not loosen the upper screws, plate
B. Do not cut or remove the ground strap.
C. Insert the 3 screws through each power cord Red or
terminal ring and back into the terminal block. Be Black
certain the white wire is in the (:enter. Securely
tighten each screw (35 to 50 in-lbs.)
Power Cord
Power cord
\ White
FOR CONDUIT INSTALLATION
A. Loosen the 3 lower screws on the terminal block. Do not
loosen the upper screws.
B. Do not cut or remove the ground strap,
Terminal
C. Insert the bare wire tip (insulation stripped 5/8") into the
bottom terminal block openings, Be certain the white
wire is in the (:enter, On certain models, the wire must
be inserted through an opening in the ground strap,
Securely tighten each screw onto each wire (35 to 50
Wire
in-lbs.), tips
NOTE; Aluminum building wire may be used but it must be
rated for the correct amperage and voltage,
Conduit
Black
Red or
Black
PROCEEDTO STEP7.
Conduit
r_ 4-WIRE INSTALLATION (SEPARATE GROUND WIRE)
AWARNING:
Shock Hazard
The neutral wire and ground strap must be
connected as shown below for the range to
be properly grounded. Do not remove the
ground strap. Failure follow this instruction
may result in potential shock hazard.
AWARNING:
Fire hazard
Terminal block screws must be securely
tightened.Failureto do so may resultin
potentialfire hazard.
FOR POWER CORD INSTALLATION
A. Remove the 3 lower screws from the
terminal block. Do not loosen the upper screws.
After-Power Cord
B. Remove the ground screw and ground plate
and retain them.
C. Cut the ground strap below the terminal __,_ #___
block and discard the lower section. Terminal
D. Insert the ground screw through the ground block ,._I_I
plate (removed earlier) and back into the °_X-
range frame. Tighten securely, but do not
over-tighten (15 to 20 in-lbs.) Red or
E. Insert the 3 terminal screws through each Black _ \x_
power cord terminal ring and back into the
terminal block. Be certain the white wire is
in the (:enter. Securely tighten each screw
(35 to 50 in-lbs.
FOR CONDUIT INSTALLATION
A. Remove the 3 lower screws from the
terminal block. Do not loosen the upper screws.
B. Remove the ground screw and ground plate
and retainthem.
Before-Power Cord and Conduit
Terminal //_--_/L_'x_XX_ Ground strap
block -- ii-_}l or
Ground f _ _,
strap Neutral
terminal
White ,_
Ground _
screw
or Bare
After-Conduit
Neutral
Ground plate
(grounding to
range)
\
Red or
Black
C. Cut the ground strap below the terminal block
and discard the lower section.
D. Insert the bare ground bare wire tip (insulation),e![_l, inal --'-'_
stripped 5/8") between the range frame
UIUt_R
and the ground plate (removed earlier)
and secure it in place with the ground Wire
screw. Tighten securely, but do not over- tips
tighten (15 to 20 in-lbs).
E. Insert the wire tips (insulation stripped 5/8") Black
into the bottom terminal block openings. Be
certain the white wire is in the center. On
certain models, the wire must be inserted Ground
through an opening in the ground strap, screw
Securely tighten each screw onto each wire
(35 to 50 in-lbs.)
Ground plate
(grounding to
_ange)
Red or_
Green
or Bare
NOTE: Aluminum building wire may be used but it must be rated for the correct amperage and voltage.
31-10980 08-14 GE