Panasonic WH-SDC0509L3E5 Manual De Instalación página 6

Drain elbow and hose installation
• Fix the drain elbow 2 and packing 3 to the bottom of Indoor Unit,
as shown in below illustration.
• Use inner diameter 17 mm drain hose in the market.
• This hose must to be installed in a continuosly downward direction
and in a frost-free environment.
• Guides this hose's outlet to outdoor only.
• Do not insert this hose into sewage or drain pipe that may generate
ammonia gas, sulfuric gas, etc.
• If necessary, use hose clamp to further tighten the hose at drain
hose connector to prevent leakage.
• Water will drip from this hose, therefore the outlet of this hose must
be installed in an area where the outlet cannot become blocked.
• If drain hose is in the room (where dew may form), please increase
the insulation by using POLY-E FOAM with thickness 6 mm or
above.
Packing 3
Drain Elbow 2
CONNECT THE CABLE TO
5
THE INDOOR UNIT
This section is for authorised and licensed electrician only. Work
behind the Control Board Cover 6 secured by screws must
only be carried out under supervision of qualifi ed contractor,
installation engineer or service person.
Open the Control Board Cover 6
Please follow the steps below to open control board cover. Before
opening the control board cover of Indoor Unit, always switch off all
power supply (i.e. Indoor Unit power supply, heater power supply).
1. Remove the 4 mounting screws at the control board cover.
2. Swing the control board cover to the right hand side.
6
WARNING
CAUTION
Screws
Screws
Fixing of Power Supply Cord and Connecting Cable
1. Connecting cable between Indoor Unit and Outdoor Unit shall be
approved polychloroprene sheathed fl exible cord, type designation
60245 IEC 57 or heavier cord.
See below table for cable size requirement.
Model
Indoor Unit
WH-WDG05LE5*
WH-SDC0509L3E5
WH-WDG07LE5*
WH-SDC0509L6E5
WH-WDG09LE5*
• Ensure the colour of wires of Outdoor Unit and the terminal
no. are the same to the Indoor Unit respectively.
• Earth wire shall be longer than other wires as shown in the
fi gure for the electrical safety in case of the slipping out of the
cord from the Holder (Clamper).
2. An isolating device must be connected to the power supply cable.
• Isolating device (disconnecting means) should have minimum
3.0 mm contact gap.
• Connect the approved polychloroprene sheathed power
supply 1 cord and power supply 2 cord and type designation
60245 IEC 57 or heavier cord to the terminal board, and to
the other end of the cord to isolating device (Disconnecting
means). See below table for cable size requirement.
Model
Indoor Unit Outdoor Unit
WH-WDG05LE5*
WH-SDC0509L3E5 WH-WDG07LE5*
WH-WDG09LE5*
WH-WDG05LE5*
WH-SDC0509L6E5 WH-WDG07LE5*
WH-WDG09LE5*
3. To avoid the cable and cord being damaged by sharp edges, the
cable and cord must be passed through a bushing (located at the
bottom of Control Board) before terminal board. The bushing must
be used and must not be removed.
Terminals on the Outdoor Unit
Colour of wires (Connecting cables)
Terminals on the Indoor Unit
(Power Supply Cord)
Terminals on the isolating devices
from power supply (Disconnecting
means)
Power Supply 1 Power Supply 2
RCCB/ELCB
*1
Holder
(Clamper)
Power Supply 1 Cable Power Supply 2 Cable
Terminal screw
M4
M5
*1 - Earth wire must be longer than other cables for safety reasons
Connecting Cable Size
Outdoor Unit
4 x min 2.5 mm
Power
Isolating Recommended
Supply Cable Size
Devices
Cord
1 3 x min 2.5 mm 2 25A 30mA, 2P, type A
2
2 3 x min 1.5 mm 15/16A 30mA, 2P, type AC
1 3 x min 2.5 mm 2 25A 30mA, 2P, type A
2
2 3 x min 4.0 mm 30A 30mA, 2P, type AC
1
L N L N 1
1 1
Indoor Unit/
L N L N
Outdoor Unit
1 1
connection
Terminal Board
Holder
(Clamper)
Connecting Cable
Tightening torque cN•m {kgf•cm}
157~196 {16~20}
196~245 {20~25}
2
RCD
2 3
2 3
*1