GBC Inspire+ A4 Guia Del Usuario página 5

Pouch Description
75 micron (2 x 75 micron)
100 micron (2 x 100 micron)
125 micron (2 x 125 micron)
175 micron (2 x 175 micron)
250 micron (2 x 250 micron)
Setting up and switching on the laminator
(1 – 4)
• Set the laminator up on a stable surface (e.g. table) close to a
mains outlet.
Ensure there is sufficient space behind the unit so the laminated
item is not blocked and can easily be removed.
• Connect mains cord with mains socket.
• Put the temperature switch in the
pouches and for cold pouches.
Inserting the document into the pouch
• Insert the document into the laminating pouch. Align it to the
sealed edge as much as possible and maintain even margins left
and right.
Pouches that are too large can be trimmed to size after lamination.
Laminating
6
• When the POWER/READY LED indicator lights green, insert the
pouch with the sealed edge first until it gets pulled in.
The laminated document automatically exits at the output side.
Letting the laminated document cool down
• Remove the laminated document and leave it on a flat surface for
one minute to cool down.
• When you have no further documents to laminate, switch off the
laminator.
Clearing a jammed pouch
• Jamming can occur when laminating unsuitable materials.
CAUTION: To prevent any damages to the laminator, the pouch must
be removed before switching off the unit.
• Move the release lever to the right and pull out the pouch
immediately.
• Clean the rollers after any pouch jam as described in section
"Maintenance and care".
Maintenance and care
WARNING: UNPLUG THIS PRODUCT BEFORE CLEANING THE
EXTERIOR. WIPE EXTERIOR ONLY WITH A DAMP CLOTH AND
DO NOT USE DETERGENTS OR SOLVENTS.
Regularly feed a cleaning card or sheet of paper through the
laminator to clean the rollers. Cleaning sheet order code: EK50000.
Machine Inspire+ Inspire+
Setting A4 A3
75 micron
100 micron
 
125 micron
175 micron  
250 micron  
position for 75-125 micron
5
7
8
Instruction Manual
Troubleshooting
Problem Possible cause
Document may be too
thick to laminate
Pouch does not
completely seal
the item
Incorrect pouch
thickness is being used
Pouch has waves or Incorrect pouch
bubbles thickness is being used
Pouch is lost in the
Pouch is jammed
machine
Pouch was sealed
'open end' first
Pouch was not centred
on entry
Pouch was not straight
Jamming
on entry
Empty pouch was used
Thick document or
foreign object was
laminated
Pouch is damaged Damaged rollers or
after lamination adhesive on rollers
Waste Electrical and Electronic
Equipment (WEEE)
Electrical and electronic devices contain materials and
substances that can have damaging effects on human
health and the environment. This symbol indicates that
this device must not be treated as unsorted municipal waste but
must be collected separately. Dispose of the device via a collection
point for the recycling of waste electrical and electronic equipment
within the EU, UK and in other European countries that operate
separate collection systems for waste electrical and electronic
equipment. By disposing of the device in the proper manner, you
help to avoid possible hazards for the environment and public
health that could otherwise be caused by improper treatment of
waste equipment. The recycling of materials contributes to the
conservation of natural resources.
Guarantee
Operation of this machine is guaranteed for one year from date
of purchase, subject to normal use. Within the guarantee period,
ACCO Brands will at its own discretion either repair or replace the
defective machine free of charge. Defects due to misuse or use
for inappropriate purposes are not covered under the guarantee.
Proof of date of purchase will be required. Repairs or alterations
made by persons not authorised by ACCO Brands will invalidate
the guarantee. It is our aim to ensure that our products perform to
the specifications stated. This guarantee does not affect the legal
rights which consumers have under applicable national legislation
governing the sale of goods.
EN
Solution
Check the thickness
of the pouch and
the document to be
laminated do not
exceed the max.
throughput thickness
Check that the pouch
thickness is correct
for the machine and
setting used
Check that the pouch
thickness is correct
for the machine and
setting used
Operate the manual
reverse lever on the
rear of the machine.
This will separate the
rollers and allow the
pouch to be manually
pulled out by hand
Pass GBC cleaning
sheets (SKU:
EK50000) through the
machine to test and
clean the rollers
5