Black and Decker BHSMP2008 Manual De Instrucciones página 12

ENGLISH
Removing the squeegee from the hand nozzle
Push the peg of the squeegee (19) forward to release
u
hand nozzle.
Rotate hand nozzle and unclip hand nozzle latches (18)
u
from squeegee rear hooks (20) and pull away from each
other.
Hints for optimum use
General
Caution: Never use the steam mop without first attaching a
cleaning pad.
Always vacuum or sweep the floor before using the steam
u
mop.
The easiest way to use the floorhead is to tilt the floorhead
u
tube to a 45º angle and clean slowly, covering a small
area at a time.
Use water only with no additives or chemicals with your
u
steam mop. To remove stubborn stains from vinyl or
linoleum floors, you can pre-treat with a mild detergent
and some water before using the steam mop.
Steam Cleaning with the mop
Fit steam handle to the floor extension.
u
Place a cleaning pad (14) on the floor with the velcro 'loop'
u
side facing up.
Lightly press the steam mop down onto the cleaning pad (14).
u
Connect the steam mop to the mains.
u
Press the ON/OFF button (1). It takes approximately 180
u
seconds for the boiler to heat up.
Once boiler is up to temperature, adjust the flow rate to
u
the required setting and press the trigger (11b) to start
steam flow.
It takes a few seconds for steam to enter the cleaning pad.
u
The steam mop will now glide easily over the surface to be
cleaned.
Push and pull the steam mop slowly across the surface to
u
thoroughly steam clean each section.
When you have finished using the steam mop, release the
u
trigger to stop steam flow, return to an upright position,
making sure that it is supported and turn "OFF". Wait until
the steam mop cools down (Approx 10 mins).
Caution! It is important to monitor the water level in the water
tank. Red indicator light will illuminate when tank is empty.
To refill the water tank and continue to clean stand the mop
upright making sure the steam trigger is not pressed.
Caution! Never leave the steam mop in one spot on any
surface for any period of time. Always place the steam mop
supported in the upright position when stationary and make
sure the steam mop is turned off when not in use.
After use
Wait until the steam mop cools down.
u
Unplug the steam mop from the electrical wall outlet.
u
12
(Original instructions)
Empty the water tank.
u
Remove the cleaning pad (14) and wash it ready for next
u
use (take care to follow the wash care instructions printed
on the cleaning pad).
Accessories
The performance of your appliance depends on the accessory
used. BLACK+DECKER accessories are engineered to high
quality standards and designed to enhance the performance
of your appliance. By using these accessories you will get the
very best from your equipment.
Garment steam cleaning (Fig. G)
Attach the hand nozzle (9) to the steam handle (11).
u
Attach the hand nozzle sock (13) around the hand nozzle
u
(9).
Note! The hand nozzle (9) should not be used without the
hand nozzle sock (13).
Connect the steam mop to the mains.
u
Press the ON/OFF button (1). The green indicator light will
u
illuminate when the boiler is up to the temperature.
Note! When first filled or after running dry, it can take up to
180 seconds for steam to be produced.
Once boiler is up to temperature, Press the required
u
steam setting button to start steam flow.
When you have finished using the steam mop, press the
u
steam flow button to stop steam flow, return to an upright
position, making sure that it is supported and turn "OFF".
Wait until the steam mop cools down (Approx 5 mins).
Using the wallpaper stripper
Check the state of your plaster before you start work
u
as high temperature steam can loosen weak, porous or
poorly bonded plaster. Plaster is also loosened more
readily in areas of cracks, holes or if the steam plate is
held in one position for too long.
You may be able to detect if you have weak plaster by
u
tapping a few areas of the walls with your knuckles. If this
produces a hollow sound, we recommend proceeding only
with extreme care.
In all cases test out the wallpaper stripper on a small area,
u
about 100 cm , before starting work properly.
2
If at any stage finishing plaster is loosened or you hear a
u
crack, do not continue. The wallpaper stripper is safe for
drywall/plaster board surfaces.
Due to the heat generated by this product, it is possible
u
that certain surfaces, ie. carpets, soft furniture, table tops,
cabinets etc., could be marked or damaged. To prevent
this, ensure a wooden board or other barrier is placed
under the boiler to prevent the heat damaging the surface.
Dust sheets or newspapers are not adequate for this
purpose.