Publicidad
Idiomas disponibles
Idiomas disponibles
For best results, remove wallpaper with a scraper. Scrape
u
off wallpaper in a downward direction.
Always wear protection when removing wallpaper from the
u
ceiling. Be careful of condensation collecting in the steam
plate as hot water may drip.
Empty the steam plate regularly and never use directly
above your head.
Always place the steam plate in a suitable container when
u
left unattended, even for a few seconds, and keep the
steam plate facing away from you when in use.
Accessories storage (Fig. H)
Small accessories along with the floorhead are stored on the
rear of the unit.
The floorhead and tube can be located on the accessory
storage (4). Locate the hook at the rear of the floorhead (6) and
slide into the slot provided on the storage as see in (Fig H).
Push firmly down and make sure the floorhead and tube are
stable before releasing
Protecting the environment
Z
Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste.
Products and batteries contain materials that can be
recovered or recycled, reducing demand for raw materials.
Please recycle electrical products and batteries according
to local provisions. Further information is available at
www.2helpU.com
Technical Data
Voltage
V
ac
Power
W
Tank Capacity
ml
Weight
kg
Troubleshooting
If your appliance seems not to operate properly, follow the
instructions below. If this does not solve the problem, please
contact your local BLACK+DECKER repair agent. Details of
your nearest BLACK+DECKER repair agent can be found on
www.2helpu.com'
Problem
Step
1.
The steam mop is not
turning on
2.
3.
BHSMP2008
BHSMP2314
230
2000
1200
5.9
Possible solution
Check the unit is plugged in at the wall
socket
Check the unit is switched on using the
ON/OFF switch (1)
Check the fuse in the plug
(Original instructions)
The steam mop is not
producing steam
The steam mop stops
producing steam
during use
The steam mop is
producing too much
steam during use
The steam mop is
producing too little
steam during use
Where can I get further
information/
accessories
Maintenance
Your BLACK+DECKER tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
@
care and regular cleaning.
Warning! Before performing any maintenance on
the tool.
Š Wipe your appliance over using a soft damp cloth.
Š For stubborn marks you can use a mild solution of soap
and water to dampen your cloth.
Guarantee
230
Black & Decker is confident of the quality of its products
2300
and offers consumers a 24 month guarantee from the date
1200
of purchase. This guarantee is in addition to and in no way
6.1
prejudices your statutory rights.
The guarantee is valid within the territories of the United
Kingdom, the Member States of the European Union and the
European Free Trade Area and the United Kingdom.
To claim on the guarantee, the claim must be in accordance
with Black&Decker Terms and Conditions and you will need to
submit proof of purchase to the seller or an authorised repair
agent. Terms and conditions of the Black&Decker 2 year
guarantee and the location of your nearest authorised repair
agent can be obtained on the Internet at www.2helpU.com, or
by contacting your local Black & Decker office at the address
indicated in this manual.
Please visit our website www.blackanddecker.co.uk to register
your new Black & Decker product and receive updates on new
products and special offers.
ENGLISH
The steam mop will only produce steam once
the unit is switched on. The white indicator
light will illuminate when power is on. The
4.
green indicator light will illimuate when the
boiler is up to the termperature and then the
steam flow trigger has been pressed on
Check that the water tank is full. If red
indicator light is on then the tank is empty.
Note: When first filled or after running dry it
5.
will take time to heat up, the green indicator
light will illuminate when the boiler is up to the
temperature.
6.
Check steps 1, then 2, then 3, then 4
7.
Check steps 4, then 5, then 3
The unit has variable steam flow settings. Set
8.
the steam flow to low steam by rotating the
dial on the steam handle.
The unit has variable steam flow settings. Set
9.
the steam flow to high steam by rotating the
dial on the steam handle.
http://www.blackanddecker.co.uk
10.
http://www.blackanddecker.ie
13
Publicidad
