DeWalt DCD800 Traducido De Las Instrucciones Originales página 19

DRILL DCD800
DRILL/HAMMERDRILL DCD805
Congratulations!
You have chosen a D WALT tool. Years of experience, thorough
e
product development and innovation make D
most reliable partners for professional power tool users.
Technical Data
Voltage
Type
Battery type
No‑load speed
1st gear
2nd gear
Impact rate
1st gear
2nd gear
Max. torque (hard/soft)
Chuck capacity
Maximum drilling capacity
Wood
Metal
Masonry
Weight (without battery pack)
Noise values and/or vibration values (triax vector sum) according to
EN62841‑2‑1:
L (emission sound pressure level)
PA
L (sound power level)
WA
K (uncertainty for the given sound level) dB(A)
Drilling into metal
Vibration emission value a
h,D
Uncertainty K =
Drilling into concrete
Vibration emission value a
h,ID
Uncertainty K =
The vibration and/or noise emission level given in this information
sheet has been measured in accordance with a standardised test
given in EN62841 and may be used to compare one tool with
another. It may be used for a preliminary assessment of exposure.

WARNING: The declared vibration and/or noise emission level
represents the main applications of the tool. However if the tool is
used for different applications, with different accessories or poorly
maintained, the vibration and/or noise emission may differ. This may
significantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration and/or noise
should also take into account the times when the tool is switched
off or when it is running but not actually doing the job. This may
significantly reduce the exposure level over the total working period.
WALT one of the
e
DCD800
V 18
DC
2
Li‑Ion
min ‑1 0–650
min ‑1 0–2000
min —
‑1
min —
‑1
Nm 90/27
mm 1.5–13.0
mm 55
mm 13
mm —
kg
1.28
dB(A) 77
dB(A) 85
5
= m/s 2 < 2.5
m/s 2 1.5
= m/s 2 —
m/s 2 —
Identify additional safety measures to protect the operator from
the effects of vibration and/or noise such as: maintain the tool
and the accessories, keep the hands warm (relevant for vibration),
organisation of work patterns.
EC‑Declaration of Conformity
Machinery Directive
DCD805
18
2
Drill/Impact Drill
Li‑Ion
DCD800, DCD805
D WALT declares that these products described under
e
0–650
Technical Data are in compliance with:
0–2000
2006/42/EC, EN62841‑1:2015+A11:2022, EN62841‑2‑
1:2018+A11:2019.
These products also comply with Directive 2014/30/EU and
0–11050
2011/65/EU. For more information, please contact D
0–34000
the following address or refer to the back of the manual.
90/27
The undersigned is responsible for compilation of the technical
1.5–13.0 file and makes this declaration on behalf of D
55
13
13
Markus Rompel
1.34
Vice‑President Engineering, PTE‑Europe
D WALT, Richard‑Klinger‑Straße 11,
e
65510, Idstein, Germany
26.07.2023
93
101
THE SUPPLY OF MACHINERY (SAFETY) REGULATIONS
5
< 2.5
1.5
11
D WALT declares that these products described under
e
1.5
Technical Data are in compliance with:
The Supply of Machinery (Safety) Regulations, 2008, S.I.
2008/1597 (as amended),
EN62841‑1:2015+A11:2022, EN62841‑2‑1:2018+A11:2019.
These products conform to the following UK Regulations:
Electromagnetic Compatibility Regulations, 2016, S.I.2016/1091
(as amended).
The Restriction of the Use of Certain Hazardous Substances
in Electrical and Electronic Equipment Regulations 2012, S.I.
2012/3032 (as amended).
For more information, please contact D
address or refer to the back of the manual.
DECLARATION OF CONFORMITY
2008
DRILL/IMPACT DRILL
DCD800, DCD805
WALT at the following
e
EnGLIsH
WALT at
e
WALT.
e
19